Products
- EMI Absorbing Clamp
- 30 - 1000 MHz
- acc. CISPR 16 for interference power with silicon-coated rolls
- Also for shielding measurements on coax. cables
The double telescopic antenna mast/tripod is continuously height-adjustable. The mast rods are made of glass fiber to avoid unwanted reflexions. The modular design makes it possible to use different telescope parts and it can be mounted on a mast foot made of stainless steel or one made out of low-reflective fiberglass. Both of them provide a secure stand and easy adjustment on uneven ground. Antennas or adapters can be mounted on the 3/8" male thread.
The original EMC EPS 70x150cm Support is white Expanded Polystyrene (EPS)
- 150 x 100 x 70 cm.
- Sit on top of a standard 80cm test table for a 150cm height
- < 1.04 Permittivity
- A new design can be pre-built or shipped flat, self-assembled, glued onsite
The Conformity Assessment Business Model DCS06 Clamp is designed and tuned for optimal operation in the 100 kHz frequency range and provides efficient coupling of the Defence Standard 59-411 DCS06 pulse to the EUT at voltages up to 1 kV (single turn output) and 4 kV (4 turn output). A single turn monitor loop is provided for pulse amplitude measurement during the test.
The High-Voltage Pulse Generator IPG 1201 is designed for testing of impulse dielectric strength of components, insulation, air- and surface flashover gaps. It is specially used for testing surge withstand capability of insulation between accessible parts and hazardous live parts, e.g. terminals for connection of antenna and mains supply terminals, refer to EN 60065. Picture: incl. Option PA 503
In accordance with the pulse verification requirements given in Annex C of ISO 7637-2:2011 and Annex A of ISO 16750-2:2012, test pulses generated by automotive transient generators need to be verified both under no-load (open circuit verification) and loaded conditions with specified loads.
The optoUSB-2.0 system can be used for the optical transmission of USB-signals up to a data rate of 480 Mbit/s according to USB2.0. It can be used to transmit USB-signals over long distances or to handle ground potential problems. With the optical transmission and the shielded case, the system is well equipped for EMI and EME tests.
- optoUSB2.0 USB hub with 4 USB ports (not as EMI robust as -RBRIR version)
- optoUSB2.0-VA6K uses a Rosenberger connector which has been proven to be more EMI robust)
- optoUSB3.0 USB hub with 2 USB ports (not as EMI robust as 2.0-RBRIR version)
The High-Voltage Pulse Generator IPG 255 is designed for testing of impulse dielectric strength of components, insulation, air-and surface flash-over gaps of watt-hour meters, static relays etc. according to IEC 60255, EN 61036, VDE 0435 part 303. Picture: incl. Option PA 503
High-Voltage Pulse Generators IPG 1218 / 1012 / 605 generate standard impulse voltages with waveform 1.2 / 50 µs acc. to IEC 60060. They are designed for testing impulse dielectric strength of components, insulations, air- and surface flash-over gaps acc. to IEC. The peak value of the test voltage is continuously adjustable from 0.2 - 6.25 / 10 / 12 kV. Positive or negative polarity of the output voltage can be selected. A built-in voltage divider 1000:1 allows monitoring of the impulse output waveform during testing.
High-Voltage Pulse Generator PG 12-400 generates standard impulse voltages with waveform 1.2 / 50 µs acc. to IEC 60060. It is designed for testing impulse dielectric strength of components, insulations, air- and surface flash-over gaps acc. to IEC.
