NNBM 8124, 10 kHz - 150(400) MHz, High Voltage, 70A, single path, 5µH LISN
NNBL 8226-2, 9 kHz - 100 MHz, 70A, 50µH, Two Path LISN
NNBL 8226-HV, 9 kHz - 100 MHz, 70A, 50µH, Single Path LISN
NNBL 8226, 9 kHz - 100 MHz, 70A, 50µH, Single Path LISN
NNBL 8225, 9 kHz - 100 MHz, 20A, 50µH, Single Path LISN
NNBL 8229-HV, 9 kHz - 100 MHz, 200A, 50µH Single Path LISN
CMDM 8700 B Common mode / Differential mode switch
NNBL 8230, 9 kHz - 100 MHz, 300A, 50µH Single Path LISN
CAP 10-8226-2, 10 µF Capacitor for MIL-STD-461 CS101, CS106
VTSD 9561 F, 10dB, Diode Pulse Limiter
VTSD 9561 D, 20dB, Diode Pulse Limiter
Products
EMSCOPE, 9kHz - 110MHz, 2 channel Receiver/LISN
EMI Measurements:
- FFT-based dual-channel receiver
- According to CISPR16-1-1
- Peak, Quasi-Peak, and Average Detectors
- Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
- The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)
NNBM 8124, 10 kHz - 150(400) MHz, High Voltage, 70A, single path, 5µH LISN
- Acc. to CISPR 25 Ed. 4, CISPR 16-1-2, DO 160, MIL-STD, or ISO 7637-2
- impedance (5µH + 1 Ohm) || 50 Ohm
- 70 A, 1000 V (DC)
- Switchable 50Ohm Load on measurement port
- 1 microfarad capacitor to ground on AE side
- BNC-jack (Type N option)
NNBL 8226-2, 9 kHz - 100 MHz, 70A, 50µH, Two Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 500VDC / 250VAC 50/60Hz / 140VAC 400Hz
- Max current 70A (100A Short time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
NNBL 8226-HV, 9 kHz - 100 MHz, 70A, 50µH, Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 800VDC / 800VAC 50/60Hz / 140VAC 400Hz
- Max current 70A (100A Short time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
NNBL 8226, 9 kHz - 100 MHz, 70A, 50µH, Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 250VDC / 250VAC 50/60Hz / 140VAC 400Hz
- Max current 70A (100A Short time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
NNBL 8225, 9 kHz - 100 MHz, 20A, 50µH, Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 250VDC / 250VAC 50/60Hz / 140VAC 400Hz
- Max current 20A
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
NNBL 8229-HV, 9 kHz - 100 MHz, 200A, 50µH Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 1000VDC / 800VAC 50/60Hz
- Max current 200A
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
CMDM 8700 B Common mode / Differential mode switch
The measurement mode switch CMDM 8700 B expands the measurement possibilities of two V-LISN to T- and Delta-LISNs for the profound analysis of interference emissions.
NNBL 8230, 9 kHz - 100 MHz, 300A, 50µH Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 250VDC / 250VAC 50/60Hz / 140VAC 400Hz
- Max current 300A, (500A limited time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
CAP 10-8226-2, 10 µF Capacitor for MIL-STD-461 CS101, CS106
To be compliant to the standards DEF STAN 59 and DO 160 a 10 μF capacitor like the CAP 10 has to be connected to the mains connectors of the LISN.
VTSD 9561 F, 10dB, Diode Pulse Limiter
Diode Pulse Limiter with built-in 10 dB high power attenuator and fuse lamp to protect sensitive measuring equipment when measuring spectra with high energy. Thanks to the built-in fuse lamp, serious overload situations of sensitive equipment can be recognized fast and reliably. A replacement bulb is placed inside the unit. The pulse limiter prevents expensive equipment defects. The very flat frequency response allows high measurement accuracy, even if only a few sample values are used for correction.
VTSD 9561 D, 20dB, Diode Pulse Limiter
Diode Pulse Limiter with built-in 20 dB high power attenuator and fuse lamp to protect sensitive measuring equipment when measuring spectra with high energy. Thanks to the built-in fuse lamp, serious overload situations of sensitive equipment can be recognized fast and reliably. A replacement bulb is placed inside the unit. The pulse limiter prevents expensive equipment defects. The very flat frequency response allows high measurement accuracy, even if only a few sample values are used for correction.
