CABCISPR2515A, CISPR 25, 5uH, 15 A LISN
Cx 10000-xxx-xxx, 1000V, 100 - 600 amp 10mF HV Capacitor Cabinet
NSLK 8117, 9 kHz - 30 MHz, 250V / 10A, 50 µH, 2 Path LISN
NNBM 8124, 10 kHz - 150(400) MHz, High Voltage, 70A, single path, 5µH LISN
NNBM DO160-1500, 10 kHz - 400 MHz, 200A, 5µH LISN, DO-160
NNBM 8126 A890, 10 kHz - 400 MHz, 75A, 5µH LISN, DO-160
MDS 21 C, 30 - 1000 MHz, EMI Absorbing Clamp
NNBL 8226-2, 9 kHz - 100 MHz, 70A, 50µH, Two Path LISN
NTFM 8131 A, ISN for 2 unshielded Unsymetrical lines, Acc CISPR 32
EMCL 6146, 10 - 1000 MHz, EM Coupling Clamp and CAL EMCL Cal Fixture
FTC 101 C Decoupling Clamp
Products
CABCISPR2532A, CISPR 25, 5uH, 32 A LISN
CABCISPR2532A
- TEST STANDARD: CISPR 25
- 5 μH // 50 Ω LISN / Artificial Network
- Small Size 80 x 80 x 120mm
CABCISPR2515A, CISPR 25, 5uH, 15 A LISN
CABCISPR2515A
- TEST STANDARD: CISPR 25
- 5 μH // 50 Ω LISN / Artificial Network
- Small Size 35 x 80 x 120mm
Cx 10000-xxx-xxx, 1000V, 100 - 600 amp 10mF HV Capacitor Cabinet
Capacitor Cx, stand-alone
- ≥ 10 mF incl. active discharge
- 100 - 600 A AC + DC RMS
- 150 - 350 A AC RMS
- 1,000 V DC
- Screw terminal connectors M12 (M16 for 600A)
- DC power supply
- Ripple generator
NSLK 8117, 9 kHz - 30 MHz, 250V / 10A, 50 µH, 2 Path LISN
- Low cost 2 path LISN
- Line Impedance Stabilisation Network
- Connector: CEE 7/4
- 9 kHz to 30 MHz
- 250 VAC, 350 VDC, 10 A
- (50 µH+5 Ω) || 50 Ω
- CISPR 16-1-2
NNBM 8124, 10 kHz - 150(400) MHz, High Voltage, 70A, single path, 5µH LISN
- Acc. to CISPR 25 Ed. 4, CISPR 16-1-2, DO 160, MIL-STD, or ISO 7637-2
- impedance (5µH + 1 Ohm) || 50 Ohm
- 70 A, 1000 V (DC)
- Switchable 50Ohm Load on measurement port
- 1 microfarad capacitor to ground on AE side
- BNC-jack (Type N option)
NNBM DO160-1500, 10 kHz - 400 MHz, 200A, 5µH LISN, DO-160
- Measurement of interference voltage in vehicles, aircraft, and ships
- 10 kHz - 400 MHz
- 1500VDC / 650VAC up to 400Hz
- Max current 200A, (280A limited time)
- Impedance of each path: 5 µH || 50 Ω ±20 %
NNBM 8126 A890, 10 kHz - 400 MHz, 75A, 5µH LISN, DO-160
- Measurement of interference voltage in vehicles, aircraft, and ships
- (1)10 kHz - 400 MHz
- 600VDC / 530VAC up to 400 Hz, 270VAC up to 890 Hz
- Max current 70A, (100A limited time)
- Impedance of each path: 5 µH || 50 Ω ±20 %
MDS 21 C, 30 - 1000 MHz, EMI Absorbing Clamp
- EMI Absorbing Clamp
- 30 - 1000 MHz
- acc. CISPR 16 for interference power with silicon-coated rolls
- Also for shielding measurements on coax. cables
NNBL 8226-2, 9 kHz - 100 MHz, 70A, 50µH, Two Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 500VDC / 250VAC 50/60Hz / 140VAC 400Hz
- Max current 70A (100A Short time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
NTFM 8131 A, ISN for 2 unshielded Unsymetrical lines, Acc CISPR 32
- T-ISN 150 Ohm asymmetric
- BNC-jack 50 Ohm unsymmetric
- 2-wire
- 400 V, 3 A AC
- 9 kHz - 30 MHz
- EN55015-2002, CISPR 32, CISPR 15, CISPR 16-1-2
EMCL 6146, 10 - 1000 MHz, EM Coupling Clamp and CAL EMCL Cal Fixture
- Common-Mode Absorbing Clamp
- Usable frequency range: 10kHz - 1000MHz
- Meets EN / IEC 61000-4-6
- Cable bundles maximum diameter of 25 mm
- Optional Cal Fixture: CAL EMCL
FTC 101 C Decoupling Clamp
Decoupling Clamp
Improve decoupling between the injection clamp and auxiliary equipment.
The FTC 101 C is a ferrite decoupling clamp for conducted immunity setups using the EMCL 6146 RF-injection clamp. It increases isolation toward auxiliary equipment (AE) in IEC/EN 61000-4-6 testing while accommodating cables up to 25 mm in diameter.
