EMSCOPE-RX2, 9kHz - 110MHz, 2 channel Receiver
EMSCOPE-RX4, 9kHz - 110MHz, 4 channel Receiver for 3 phase
EMScanner: 150 kHz- 8 GHz, 3.5mm Resolution, EMC desktop scanner
EMScannerR: 150 kHz- 8 GHz, 0.06mm resolution, EMC desktop scanner
EMProbe: 9kHz- 18 GHz, 0.2mm resolution, EMC robotic scanner
EM Near Field Probe Kit w/Camera & Software
RFScanner, Antenna Pattern measurement, 300MHz - 6 GHz
TBMR-110M DC - 110 MHz high speed EMI-Analyzer
LSAOL 1.0, Laser Powered RF Link, 9kHz - 6GHz w/5-12VDC 2W power sourse
LSAOL 1.1, Laser Powered RF Link, 9kHz - 6GHz
Products
EMSCOPE, 9kHz - 110MHz, 2 channel Receiver/LISN
EMI Measurements:
- FFT-based dual-channel receiver
- According to CISPR16-1-1
- Peak, Quasi-Peak, and Average Detectors
- Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
- The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)
EMSCOPE-RX2, 9kHz - 110MHz, 2 channel Receiver
EMI Measurements:
- FFT-based dual-channel receiver
- According to CISPR16-1-1
- Peak, Quasi-Peak, and Average Detectors
- Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
- The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)
EMSCOPE-RX4, 9kHz - 110MHz, 4 channel Receiver for 3 phase
EMI Measurements:
- FFT-based dual-channel receiver
- According to CISPR16-1-1
- Peak, Quasi-Peak, and Average Detectors
- Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
- The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)
- Measure 4 lines of 3 phase LISN
- The picture is shown with internal LISN [EMSCOPE RX4 LZ2]
EMScanner: 150 kHz- 8 GHz, 3.5mm Resolution, EMC desktop scanner
- Capability:
- Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, and report generation.
- Spatial scan time:
- Continuous real-time or sub-second single scan for the entire scan area is dependent on spectrum analyzer performance.
- Spectral scan time:
- 45 seconds for L 10 cm x W 10 cm (L 4” x W 4”) PCB with a 100 MHz span and 100 kHz RBW. Scanning area, span, and RBW are user-selectable within spectrum analyzer specifications
- EMViewer Software
- We recommend you use the EMViewer software for best results. A Yearly subscription or a once-off purchase is available.
- Supported operating systems: Windows 10®
- Supported CAD overlays: Standard Gerber© RS274x format and HPGL format
EMScannerR: 150 kHz- 8 GHz, 0.06mm resolution, EMC desktop scanner
- Capability:
-
- Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
- Spatial scan time:
-
- Continuous real-time for the entire scan area (1,218 probes activated) when Level 1 is selected: 5 sec.
- Selected area 2.25 cm x 2.25 cm, 9 probes activated.
- Level 1:
- Spectral scan time:
-
- 11 seconds for L 10 cm x W 10 cm (L 4” x W 4”, 178 probes activated) from 10 MHz span to 110 MHz and 122 kHz RBW. Scanning area, span, and RBW are user-selectable within spectrum analyzer specifications
- Supported operating systems: Windows 10®
- Supported overlays: Picture in JPEG format
- Standard Gerber© RS274x format and HPGL form
EMProbe: 9kHz- 18 GHz, 0.2mm resolution, EMC robotic scanner
- Capability:
- Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
- Customization of the robot arm size, any size, is possible.
- Spatial scan time:
-
- The scan time depends on size and area
- Ideal for large component boards
- The robotic arm allows for advanced scans on complex items
- Supported operating systems: Windows 10®
- Supported overlays: Picture in JPEG format
- Standard Gerber© RS274x format and HPGL form
EM Near Field Probe Kit w/Camera & Software
" A Probe Kit on Steroids"
- Fully integrated with Y.I.C. Technologies EMViewer software and EMProbe
- Normalization and correction when using the EMViewer software
- Flat response within the range of operation
- Slim Design and Protective Coating
- 18GHz Measured Cable included
RFScanner, Antenna Pattern measurement, 300MHz - 6 GHz
- Frequency Range of 300 MHz to 6.0 GHz
- Far-Field Patterns and Bisections, including EIRP / TRP / PRD, Circular and linear polarization, and axial ratio patterns
- Near-field insights such as Amplitude and Phase distribution are available in seconds
- Gain, Efficiency, and S11 chart with Supported VNAs
- “Real-time” real-fast
- Can be used to evaluate either standalone (i.e. passive) antennas or antennas that are embedded in wireless devices (i.e. active antennas).
- Simple set up and Easy to use
TBMR-110M DC - 110 MHz high speed EMI-Analyzer
The TBMR-110M EMI Analyzer is designed to carry out conducted emission measurements. Its affordability and versatility make it a perfect tool for engineers doing pre-compliance measurements during the development process.
- True DC – 110 MHz measurement range
- CISPR-16, ANSI and MIL-STD compliant detectors
- Peak, Quasi-Peak, Average, CISPR Average, RMS and CISPR RMS dectectors working in parallel
- Zero Span operation with time domain triggering
- Linear, log amplitude and frequency display
LSAOL 1.0, Laser Powered RF Link, 9kHz - 6GHz w/5-12VDC 2W power sourse
The LSAOL 1.0/1.1 Laser-Powered Analog Optical Links with integrated pre-amplifiers are low-noise RF signal transmission systems for 9 kHz to 6 GHz.
- They are ideally suited for EMC emission testing.
- The need for batteries is eliminated through laser-powered operation.
- The LSAOL Front Unit is laser-powered and equipped with both low and high-band pre-amplifiers
- LSAOL 1.0 provides an adjustable, 5 V to 12 V phantom power supply delivering up to 2W to external devices such as active antennas or pre-amplifiers.
LSAOL 1.1, Laser Powered RF Link, 9kHz - 6GHz
The LSAOL 1.0/1.1 Laser-Powered Analog Optical Links with integrated pre-amplifiers are low-noise RF signal transmission systems for 9 kHz to 6 GHz.
- They are ideally suited for EMC emission testing.
- The need for batteries is eliminated through laser-powered operation.
- The LSAOL Front Unit is laser-powered and equipped with both low and high-band pre-amplifiers
- LSAOL 1.0 provides an adjustable, 5 V to 12 V phantom power supply delivering up to 2W to external devices such as active antennas or pre-amplifiers.
