DGA 9552 N, Attenuator, 5 watts, 18GHz, 3, 6, 10, 20, 30, & 40dB
NFCN 1356, 1356 kHz Compensation Network for HFRA 5164
NFCN 9734 - DC- 200 kHz Compensation Network
NFCN 9731-100, DC- 180 Hz Compensation Network for HHS 5230-100
NFCN 9732-85, 80 - 90 kHz Compensation Network for HHS 5206-8
NFCN 9732-120, 50-60 Hz, Compensation Network for HHS 5210-100
EMCL- NW 10 / MN-1 EM Clamp Matching Network
VTSD 9561 D, 20dB, Diode Pulse Limiter
SYMAT 40, Symmetrical Step Attenuator, 100 Ohms acc. EN 50561-1
VTSD 9561 F, 10dB, Diode Pulse Limiter
TBAS3 10W Type N Attenuator Set
Products
DGA 9553 BNC, Attenuator, 1 watts, 2GHz, 3, 6, 10, 20, and 30 dB
DGA 9553 BNC is a bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions.
There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration, an attenuator directly at the pulse generator output is inevitable.
- 3, 6, 10, 20, and 30 dB Values available
- 50 Ohm, Low VSWR
- 1 Watts
DGA 9552 N, Attenuator, 5 watts, 18GHz, 3, 6, 10, 20, 30, & 40dB
DGA 9552 N is a bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions.
There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration, an attenuator directly at the pulse generator output is inevitable.
- 3, 6, 10, 20, 30, and 40 dB Values available
- 50 Ohm, Low VSWR
- 5 Watts, 1 kW peak (5 μsec. pulse width, 0.25% duty cycle)
- Optional storage case CCA
NFCN 1356, 1356 kHz Compensation Network for HFRA 5164
- Compensation Network
- For HFRA 5164
- up to 26 A/m @ 50 Watts
- 13.56 MHz
NFCN 9734 - DC- 200 kHz Compensation Network
- Compensation Network
- For: HHS 5206-16, HHS 5204-12, HHS 5202-9
- up to 32 Arms
- DC - 200 kHz
NFCN 9731-100, DC- 180 Hz Compensation Network for HHS 5230-100
- Compensation Network
- For HHS 5230-100
- up to 8 Arms
- DC - 180 kHz
NFCN 9732-85, 80 - 90 kHz Compensation Network for HHS 5206-8
- Compensation Network
- For HHS 5206-8
- up to 11 Arms
- 80 - 90 kHz (85 kHz)
NFCN 9732-120, 50-60 Hz, Compensation Network for HHS 5210-100
- Compensation Network
- For HHS 5210-100
- up to 151 Arms
- 50 - 60 Hz
EMCL- NW 10 / MN-1 EM Clamp Matching Network
EMCL- NW 10 / MN-1 Matching Network • For use with the EMCL-20 in the frequency range 10 kHz – 150 kHz • For use with the CDN BCI-P1 in the frequency range 10 kHz – 150 kHz
VTSD 9561 D, 20dB, Diode Pulse Limiter
Diode Pulse Limiter with built-in 20 dB high power attenuator and fuse lamp to protect sensitive measuring equipment when measuring spectra with high energy. Thanks to the built-in fuse lamp, serious overload situations of sensitive equipment can be recognized fast and reliably. A replacement bulb is placed inside the unit. The pulse limiter prevents expensive equipment defects. The very flat frequency response allows high measurement accuracy, even if only a few sample values are used for correction.
SYMAT 40, Symmetrical Step Attenuator, 100 Ohms acc. EN 50561-1
- Symmetrical 100 Ω step attenuator
- Switchable between 0 dB, 10 dB, 20 dB, 30 dB, 40 dB and 50 dB
- For measurement of PLC or PLT to discover dynamic performance
- Acc. EN 50561-1:2012 chapter 9.2. Figure 4 shows the setup
VTSD 9561 F, 10dB, Diode Pulse Limiter
Diode Pulse Limiter with built-in 10 dB high power attenuator and fuse lamp to protect sensitive measuring equipment when measuring spectra with high energy. Thanks to the built-in fuse lamp, serious overload situations of sensitive equipment can be recognized fast and reliably. A replacement bulb is placed inside the unit. The pulse limiter prevents expensive equipment defects. The very flat frequency response allows high measurement accuracy, even if only a few sample values are used for correction.
TBAS3 10W Type N Attenuator Set
The TBAS3 RF 10W attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box.
