SESD 216: ESD - Simulator 16,5 kV
ESD Test Table Kit
AEMC-HVM40B ElectroStatic HV Meter
SESD 8800-4: ESD Verification Set
SESD 272 Grounding cable for ESD
SESD 271 Vertical Coupling Plate (VCP) for ESD
SESD 302x Test tip's for ESD
SESD 30 T 1000 Support arm
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
ESD-Soft 6: Control software for ESD
SESD 30000: ESD - Simulator 30 kV
Products
SESD 230: ESD - Simulator 30 kV
IEC / EN 61000-4-2 The test generator SESD 230 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods; Test voltage max. 30,0 kV AIR und CON; Discharge impedance 150pF/330 Ohm (IEC); Battery or mains operation; Predefined tests, standard and other
SESD 216: ESD - Simulator 16,5 kV
IEC / EN 61000-4-2 The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods; Air discharge (AIR) and Contact discharge (CON); Test voltage max. 16,5 kV AIR, max. 10,0 kV CON; Discharge impedance 150pF/330 Ohm (IEC); Battery or mains operation; Predefined tests - standard and other
ESD Test Table Kit
The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.
AEMC-HVM40B ElectroStatic HV Meter
- Measures 500 to 40,000 Volts DC
- Dual range switch provides increased resolution for measuring voltages below 20 kilovolts
- Extremely high input impedance (10 giga-ohms) minimizes circuit loading
- Large LED display
- Advanced solid-state design
- Retractable Flip Feet (standard)
- Retractable Tilt Handle (optional)
- Rack Mount Ears (optional)
SESD 8800-4: ESD Verification Set
ESD - Generators verified according to the standard International Electro technical Commission 61000-4-2, ISO 10605 and other. The measurements of the single pulses take place with a special 2 ohm shunt. For the correct verification of the ESD impulses an oscilloscope is necessary with a minimum bandwidth of - 2 GHz acc. IEC 61000-4-2, 2008 and - 1 GHz acc. ISO 10605, 2008. The ESD verification set SESD 8800-4 works up to 4 GHz and fulfilled the request of the double bandwidth regarding to the measurement bandwidth.
SESD 272 Grounding cable for ESD
2m Grounding cable for ESD immunity tests
SESD 271 Vertical Coupling Plate (VCP) for ESD
The Vertical Coupling Plate (VCP) is used in conjunction with ESD generators to simulate indirect discharges on metallic objects that are near a test object. The bleeder resistors contained in the ground wire of the VCP serve to prevent the applied charge from vanishing immediately after the discharge of the ESD generator to the VCP, thereby increasing the effect of the ESD test.
SESD 302x Test tip's for ESD
Avalible ESD Test Tips for replacment or different aplications.
SESD 30 T 1000 Support arm
Support arm with balancer for ESD test station
- Support arm with the carriage
- 360 degrees pivotable
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
The ESD-Sense has been developed with EMC test laboratories in mind to enable a “go / no-go” verification of the ESD generator output prior to test.
ESD-Soft 6: Control software for ESD
The Microsoft-Windows based software controls the ESD generator via a serial interface
SESD 30000: ESD - Simulator 30 kV
The ESD simulator SESD 30000 is suitable for EMC testing of systems and equipment in accordance with standard IEC / EN 61000-4-2, ISO 10605 (Automotive), MIL-STD and other. The modular structure of the simulator allows further testing according to different standards and customer definitions. Test voltage max. 30,0 kV AIR and CON; Discharge impedance IEC, ISO, MIL etc.; Modular structure, self-test; Automatic charge absorber integrated;
