TBMR-110M DC - 110 MHz high speed EMI-Analyzer
TBFL1 - Transient Limiter
TBPS01 EMC NEAR-FIELD PROBES + TBWA2/40dB WIDEBAND AMPLIFIER
TBPS01 EMC NEAR-FIELD PROBES + TBWA2/20dB WIDEBAND AMPLIFIER
TBAS3 10W Type N Attenuator Set
TBCAS1 Coaxial Adapter Set
TBAS1 RF Attenuator Set
TBAS2 SMA Attenuator & Terminatation Set
TBPS01 EMC NEAR-FIELD PROBES
TBLC08 - 50uH Line Impedance Stabilization Network LISN CISPR 16
TBOH01 - 5µH Line Impedance Stabilization Network CISPR 25
Products
AB-Precompliant Test Kits
Absolute EMC has designed low-cost pre-compliance systems to meet a wide range of RF emissions and immunity needs. Some form of pre-complaint testing is a must for any company that needs to demonstrate their product for EMC compliance. This enables companies to be responsive when issues happen and to also be proactive before going to the lab to better your chances of passing the first time.
TBMR-110M DC - 110 MHz high speed EMI-Analyzer
The TBMR-110M EMI Analyzer is designed to carry out conducted emission measurements. Its affordability and versatility make it a perfect tool for engineers doing pre-compliance measurements during the development process.
- True DC – 110 MHz measurement range
- CISPR-16, ANSI and MIL-STD compliant detectors
- Peak, Quasi-Peak, Average, CISPR Average, RMS and CISPR RMS dectectors working in parallel
- Zero Span operation with time domain triggering
- Linear, log amplitude and frequency display
TBFL1 - Transient Limiter
The TBFL1 is a combined transient limiter/attenuator/ high pass filter, designed to provide optimum protection of spectrum analyzer or measurement receiver inputs when carrying out conducted noise measurements or other measurements where the input levels cannot be predicted with certainty or where accidental overloads may occur.
TBPS01 EMC NEAR-FIELD PROBES + TBWA2/40dB WIDEBAND AMPLIFIER
The H20, H10, H5, and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies. The probes act similar to wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations which emit electromagnetic radiation. By changing to a probe with a smaller size, the origination of the emissions can be further narrowed down. With TBWA2 WIDEBAND AMPLIFIER/40DB
TBPS01 EMC NEAR-FIELD PROBES + TBWA2/20dB WIDEBAND AMPLIFIER
The H20, H10, H5, and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies. The probes act similar to wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations which emit electromagnetic radiation. By changing to a probe with a smaller size, the origination of the emissions can be further narrowed down. With TBWA2 WIDEBAND AMPLIFIER/20DB
TBAS3 10W Type N Attenuator Set
The TBAS3 RF 10W attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box.
TBCAS1 Coaxial Adapter Set
The TBCAS1 coaxial adapter set contains 44 pieces of the most common 50 Ohm coaxial adapters in a beechwood box
TBAS1 RF Attenuator Set
The TBAS1 RF 2W attenuator set
TBAS2 SMA Attenuator & Terminatation Set
The TBAS2 RF SMA attenuator/termination set consists of a 3dB, 6dB, 10dB, 15dB, 20dB and 30dB SMA attenuators in a beechwood box. Furthermore, it contains two pieces SMA 50 Ohm terminations.
TBPS01 EMC NEAR-FIELD PROBES
The H20, H10, H5, and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies. The probes act similar to wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps, and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations that emit electromagnetic radiation. By changing to a probe with a smaller size, the origination of the emissions can be further narrowed down.
TBLC08 - 50uH Line Impedance Stabilization Network LISN CISPR 16
The TBLC08 is a Line Impedance Stabilization Network for the measurement of line-conducted interference within the range of 9kHz to 30MHz, according to the CISPR16 standard. The device is designed for testing single phase, AC-powered equipment with supply voltages up to maximum 240V.
TBOH01 - 5µH Line Impedance Stabilization Network CISPR 25
The TBOH01 5µH LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
