Products
The original EMC EPS Bar is white Expanded Polystyrene can optional be painted coating to extend durability. They come in dimensional metric sizes of 100 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Bar is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 4 sides allows for easy positioning and test setups.
The original EMC EPS 70cm Support is white Expanded Polystyrene. They come in dimensional metric sizes of 40 x 60 x 70 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. Since the EMC EPS 70cm Support is made from a denser EPS rating, it is crush resistance and able to withstand heavy weight loads without deforming.
The original EMC EPS Cube is white Expanded Polystyrene can optional a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 10 cm which matches EUT height requirements for IEC testing above the ground plane for IEC 61000-4-5 and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Cube is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.
The HV - Impulse generators IPG 2025 and IPG 2436 create standard impulse voltages with waveform 1.2 / 50 µs acc. to IEC 60060. They are designed for testing impulse dielectric strength of components, insulations, air- and surface flash-over gaps according to the standards. The peak value of the test voltage is continuously adjustable from 2 - 20 kV or 2 - 24 kV. Positive or negative polarity of output voltage can be selected. A built-in voltage divider 1000:1 allows monitoring of the impulse output waveform during testing.
The High-Voltage Pulse Generator IPG 1201 is designed for testing of impulse dielectric strength of components, insulation, air- and surface flashover gaps. It is specially used for testing surge withstand capability of insulation between accessible parts and hazardous live parts, e.g. terminals for connection of antenna and mains supply terminals, refer to EN 60065. Picture: incl. Option PA 503
The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.
TEM-6000 STRIPLINE Mod.2020 is a 6 GHz IC Stripline TEM Cell to generate EM fields for testing sample IC devices. It meets the requirements of IEC 61967-2/8, IEC 62132-8 and SAE 1752-3
Mini EMI Camera for Low Emission / High Field Use
- 10x Optical Zoom
- For use in smaller spaces
- Integrated microphone
- Battery or wall-powered
- Single Fiber operation (duel direction)
- Options for Pan/Tilt, Joystick, HIRF, recording, motion triggering, OCR, ...
Mini EMI Camera for Low Emission / High Field Use
- For use in very small spaces
- Integrated microphone
- Battery or wall-powered
- Single Fiber operation (duel direction)
- Options for HIRF, recording, motion triggering, OCR, ...
The infrared camera opto-LWIR was developed specifically for EMC tests. In high field strengths with directional antennas (fire protection!), an overload of the DUT or the absorbers can be detected early.
