Standards

PGESD 300K DP - Helicopter 300kV ESD Test System

• High Voltage Capability: Generates electrostatic discharges up to 300 kV with reversible polarity.
• Adjustable Electrode: Height adjustable from 1.5 to 6 meters and tilt up to ±60° for precise targeting.
• Standards Compliance: Meets MIL-STD-331, MIL-STD-464, NATO AECTP-250, AECTP-500, and more.
• Automated Operation: PC-based software for remote control, calibration, and test reporting.
• Enhanced Safety: Fiber optic interface ensures operator safety by isolating the control system from high-voltage equipment.
• Versatile Testing: Supports multiple discharge scenarios, including personnel-borne and helicopter-borne ESD tests.
• Durable Design: Built for demanding military and industrial testing environments.

• Bidirectional Optical Isolation: 20 m multimode fiber link (62.5/125 µm) for galvanic isolation of Control Pilot, CAN, and auxiliary signals.
• Long Life Battery Power: Internal 8.4 V, 4 Ah NiMH pack delivers up to 10 hours of continuous operation.
• Robust Construction: Anodized aluminum housing with rubber bumpers and grounding lug, rated for CISPR 25 Class 5 environments.
• Versatile Signal Interfaces: BNC connector for Control Pilot plus D SUB 15 female for CAN, temperature sensors, connector lock control, etc.
• Wide Protocol Support: Compatible with CCS, CHAdeMO, and GB/T charging standards for comprehensive EVSE/EV EMC testing.
• Compact & Portable: 140 × 86 × 65 mm enclosure weighing ≈760 g—ideal for on site and laboratory test setups.

MAG 1000

• 1-120A/m Contiunus testing
• 100-1100A/m Short Duration 1-3sec
• Test either 50Hz & 60Hz Selectable
• 1m square Loop

The CDG 7000 is a new test generator for all standards on immunity to conducted disturbances induced by high-frequency fields - including BCI tests (ISO 11452-4). One of the very few combined IEC 61000-4-6 test systems that contain the RF signal generator, an RF power amplifier, a 3-channel RF voltmeter, and a directional coupler at a very affordable price.

Highlights of the CS116 Damped Sinusoid Generator

• MIL-STD 461 CS115+CS116 Compliant: Meets stringent military testing standards.
• Flexible Frequency Options: Choose from 6, 9, or 17 test frequencies.
• Comprehensive Accessories: Includes injection probe, attenuator, oscilloscope, and control software.
• Efficient Operation: Single signal output reduces test time and supports automation.
• User-Friendly Control: Easily controlled via RS232 and USB interfaces.
• Robust Design: Durable construction with wide power compatibility (90–264 Vac).

Optimize your naval and industrial testing with the CS116 & CS115 Damped Sinusoid & Switch Transient Generator—precision and efficiency combined.

" An RF Probe Kit on Steroids"

• Fully integrated with Y.I.C. Technologies EMViewer software and EMProbe
• Normalization and correction when using the EMViewer software
• Flat response within the range of operation
• Slim Design and Protective Coating
• 18GHz Measured Cable included
• Lectures & Explanation Document
• Designed By Prof. Arturo Mediano, University of Zaragoza, Spain

• Frequency Range of 300 MHz to 6.0 GHz
• Far-Field Patterns and Bisections, including EIRP / TRP / PRD, Circular and linear polarization, and axial ratio patterns
• Near-field insights such as Amplitude and Phase distribution are available in  seconds
• Gain, Efficiency, and S11 chart with Supported VNAs
• “Real-time” real-fast
• Can be used to evaluate either standalone (i.e. passive) antennas or antennas that are embedded in wireless devices (i.e. active antennas). 
• Simple set up and Easy to use

Axos 5 - Compact

• Multi Tester with 16AMP CDN
• EFT/Burst 5kV IEC 61000-4-4
• Surge, Combination Wave 5kV IEC 61000-4-5
• Surge Magnetic field IEC 61000-4-9 (MSURGE-A loop antenna required)
• AC Dips/Drops IEC 61000-4-11 (DIP 116 dips transformer required)
• DC Dips/Drops IEC 61000-4-29 (2x DC supplies required)

• Capability:
• Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
• Customization of the robot arm size, any size, is possible. 
• Spatial scan time:
• • The scan time depends on size and area
• Ideal for large component boards
• The robotic arm allows for advanced scans on complex items
• Supported operating systems: Windows 10®
• Supported overlays: Picture in JPEG format 
• Standard Gerber© RS274x format and HPGL form