Standards

BOLAB´s new and world´s unique solutions in testing High Voltage profiles for Electric Vehicles are very powerful, flexible, and modular.

Three different solutions for high-speed testing, a medium-range for covering most profiles, and a low budget. Powerful solutions for starting and gaining experience are available.

Modularity is one of the most important characteristics of BOLAB´s systems.

Start with a “small” system of 1 KW (1.000 V, 15 A) and expand module by module as applications require and budgets allow.

It was never this easy to get involved with high voltage tests for Electric Vehicles and to build up these tests to a most powerful solution.

Audio Transformer 200W, 50A

• 160x155x200mm
• 2:1 ratio 
• 200 W Maximum30Hz - 250 kHz
• 100 W Maximum at15 Hz - 30 Hz
• Insulation Resistance Test - 2kV

• Capability:
• • Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
• Spatial scan time:
• • Continuous real-time for the entire scan area (1,218 probes activated) when Level 1 is selected:  5 sec.
  • Selected area 2.25 cm x 2.25 cm, 9 probes activated.
  • Level 1: 
• Spectral scan time:
• • 11 seconds for L 10 cm x W 10 cm (L 4” x W 4”, 178 probes activated) from 10 MHz span to 110 MHz and 122 kHz RBW. Scanning area, span, and RBW are user-selectable within spectrum analyzer specifications
• Supported operating systems: Windows 10®
• Supported overlays: Picture in JPEG format 
• Standard Gerber© RS274x format and HPGL form

• Capability:
• Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
• Customization of the robot arm size, any size, is possible. 
• Spatial scan time:
• • The scan time depends on size and area
• Ideal for large component boards
• The robotic arm allows for advanced scans on complex items
• Supported operating systems: Windows 10®
• Supported overlays: Picture in JPEG format 
• Standard Gerber© RS274x format and HPGL form

" A Probe Kit on Steroids"

• Fully integrated with Y.I.C. Technologies EMViewer software and EMProbe
• Normalization and correction when using the EMViewer software
• Flat response within the range of operation
• Slim Design and Protective Coating
• 18GHz Measured Cable included

• Frequency Range of 300 MHz to 6.0 GHz
• Far-Field Patterns and Bisections, including EIRP / TRP / PRD, Circular and linear polarization, and axial ratio patterns
• Near-field insights such as Amplitude and Phase distribution are available in  seconds
• Gain, Efficiency, and S11 chart with Supported VNAs
• “Real-time” real-fast
• Can be used to evaluate either standalone (i.e. passive) antennas or antennas that are embedded in wireless devices (i.e. active antennas). 
• Simple set up and Easy to use

Onyx 16

• +/- 16kV air and Contact Discharge
• 150pF/330Ohm Standard, Other networks available
• >16 hour Battery life, AC mains option
• Optional Software

Onyx 30

• +/- 30kV air and Contact Discharge
• 150pF/330Ohm Standard, Other networks available
• >16 hour Battery life, AC mains option
• Optional Software

Axos 5 - Compact

• Multi Tester with 16AMP CDN
• EFT/Burst 5kV IEC 61000-4-4
• Surge, Combination Wave 5kV IEC 61000-4-5
• Surge Magnetic field IEC 61000-4-9 (MSURGE-A loop antenna required)
• AC Dips/Drops IEC 61000-4-11 (DIP 116 dips transformer required)
• DC Dips/Drops IEC 61000-4-29 (2x DC supplies required)