Products
The CAR arbitrary waveform generator 6000 is a compact EMC testing system for performing voltage variations on supply lines of vehicles. The system strictly complies with the international standards and manufacturer standards that describe phenomena on the power supply of vehicles. Thus, the CAR arbitrary waveform generator 6000 is the optimal voltage power source for battery simulation up to 70V. It can simulate pulse 2b, pulse 4, starting profile, superimposed alternating voltage, and others, up to a battery current of 100A.
Compact EMC test unit designed for testing electromagnetic immunity of the electrical installation of vehicles and components against supply line transients. PG 2804 includes the generation of pulses #5 / Test A and Test B. It is designed to be connected to the power supply interface of the CAR-TESTER. Load Dump Generator EMC-Test Equipment for the electrical installation of vehicles.
- Puls #5 / Test A / Test B
- Ri = 0.5 / 1 / 2 / 4 / 8 Ω
- Used with CAR-SYS 14 or independently with Coupling Network.
High-Voltage DC Test Sets HTS 20-10 are designed for testing dc dielectric strength of components, insulations, air- and surface flash-over gaps. Also for testing SPDs according to IEC 61643-1. The test voltage can be adjusted from 0.2 kV up to 20 kV. The test voltage rises like a ramp from zero to the selected test voltage. The rate of rise can be adjusted from 100 V/sec up to 10000 V/sec. Then the test voltage remains at the selected value for the test time, which can be adjusted from 1 – 1000 sec. Figure: incl. option PA503
The oscillatory wave generator IPG 2554 has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory waves according to IEC 61000-4-18 requirements. It generates a decaying sine waveform with ringing frequency from 100 kHz to 30.0 MHz. These waveforms represent disturbances occurring in power, control and signal cables installed in high voltage and medium voltage stations and in heavy industrial installations.
The oscillatory wave generator IPG 2553 has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory magnetic field according to IEC 61000-4-10 requirements. It generates a decaying cosine current waveform with ringing frequency of 100 kHz or 1.0 MHz. The generator output is connected to special designed Helmholtz-coil which generates magnetic field with 10 - 100 A/m.
IPG 612T RING-WAVE GENERATOR is a High-voltage pulse generator producing Ring Wave 0.5 µs / 100 kHz acc. to IEC 61000-4-12. The output peak voltage can be preset continuously from 0.2 - 6 kV. Rise time 0.5µs to the first peak, ringing frequency 100 kHz. The picture is shown with PA 503 Option.
The GTEMCELL GTEM-1000 Family is a TEM waveguide with the upper-frequency limit extended to the GHz range. It is under consideration as an alternative measurement facility for both radiated emission and immunity measurements. It is included in the standard IEC 61000-4-20 “Emission and Immunity Testing in Transverse Electromagnetic (TEM) Waveguides”.
Model GTEMCELL GTEM250 F with Ferrite tiles on the bottom offers a wider operating bandwidth with peak smoothed and flat response starting from DC to microwave frequencies. It is an indispensable tool for researchers and developers engineers! Model GTEMCELL GTEM250 F SAE includes a special opening to test integrated circuits, dimensions: 80 mm x 80 mm on Approx. 45 mm septum height, closed from a removable panel where are placed the IC under testing.
The GTEMCELL GTEM 400 family consist of the: GTEM-400 made with 65cm pyramidal carbon-foam absorbers (RAM). GTEM-450 made with 51cm. EMC Truncated pyramidal absorbers (RAM) GTEM-450V is the vertical model (suffix V) made with 51cm. EMC Truncated pyramidal absorbers (RAM)
GTEM-500 F made with Ferrite tiles on the bottom and 45cm Hybrid pyramidal carbon-foam absorbers (RAM). GTEM-550 F made with Ferrite tiles on the bottom and 35cm Hybrid pyramidal carbon-foam absorbers (RAM). GTEM-550 VF is the vertical model (suffix V) made with Ferrite tiles on the bottom and 35cm Hybrid pyramidal carbon-foam absorbers (RAM).
