Products
The LSProbe 1.2 Variant E Field Probe is a high-speed, high-accuracy, and high-dynamic range electric-Field probe.
- Its standard frequency range of 10 kHz – 8.2 GHz. 15,000 V/m
- Best-in-class compensation of linearity, frequency, and temperature guarantees accurate measurements from less than 15 to at least 15,000 V/m.
- A dynamic range of 100 dB is achieved for many frequencies, enabling Field measurements at more than 10,000 V/m.
- Customized high Field-strength „X“-variants, supporting up to 30,000 V/m and a damage level of 100,000 V/m, are available upon request.
- Wideband Precision (9 kHz – 30 MHz): Delivers ±1 dB antenna factor stability across the full frequency range.
- Long-Life, Low?Noise Operation: Internal NiMH battery pack provides >12 hours of noise-free measurements.
- Dual-Field Capability: Supports both magnetic (–31.5 dB Ω·m) and “fictive” electric (20 dB/m) field measurements with one probe.
- Rugged, User-Friendly Design: Milled aluminum housing with LED overload indicator and versatile tripod or handle mounting.
Stacked Logarithmic-Periodic Broadband Antenna for Linear polarised RX- and TX- applications in the microwave frequency range. The antenna structure is made of laser-cut brass. For the protection of the fine antenna structure against damage, the antenna is equipped with a low loss plastic protection cover. The STLP 9149 is especially suitable for Immunity Testing acc. to IEC 61000-4-3 because of its good field uniformity.
- (0.6)0.7-9 (10.5) GHz
- Gain 10.3 dBi +/- 1.5 dBi
- Type N female
Highlights of the IP-DR250, One Probe to Unite All EMC Testing
- Frequency Range: 10 kHz to 400 MHz (extended: 4 kHz to 400 MHz with optional adapter)
- Power Handling: Up to 500 W CW (150 W – 60 min, 300 W – 30 min, 500 W – 15 min)
- Window Diameter: 43.8 mm
- Construction: Durable, shielded design with precision-machined housing
- Input Connector: Type N (Female)
- 8 kHz – 30 MHz Wideband: Delivers ±1 dB antenna-factor accuracy across the full spectrum.
- Dual-Mode Measurement: 20 dB/m (E-field) and –31.5 dB Ω·m (H-field) in one compact probe.
- Long-Life Battery Operation: NiMH pack provides over 12 hours of low-noise, mains-free measurements.
- Overload Protection: Built-in LED indicator alerts you at the 1 dB compression point.
- Ultra-Wideband – Covers up to 10 GHz
- High Accuracy – Superior phase & amplitude balance
- EMI Shielded – Ensures clean signal transmission
- Low Loss – Maintains signal integrity
- Passive Design – No power required, bidirectional flow
- Compact & Durable – SMA connectors for easy integration
The Conformity Assessment Business Model DCS12 Test Generator meets all the DCS12 wave verification parameters for testing DC, single and three-phase equipment, that is source impedance and verification of damping and frequency when measured into a 10 Ω load. Output amplitude is software adjustable with permanent memory, should re-alignment be needed during calibration.
- There are three fixed outputs: 600 V, 750 V, and 2500 V
- 15.9 kHz ±10 %
- 10.9 kHz ±10 %
- Ultra-Fast Response – Time constants from 200 ns to 12 µs for precise signal integration
- High Bandwidth – Supports frequencies up to 1.4 GHz
- Accurate Signal Reconstruction – Eliminates errors from numerical integration
- Passive & Reliable – No power required, ensuring long-term stability
- Oscilloscope-Compatible – Seamless integration with high-impedance inputs
- Versatile Connectivity – Available with N, BNC, and SMA connectors
The optoSENT system was developed for the transmission of asynchronous SENT signals (Single Edge Nibble Transfer) and exists in two different versions.
The optoSPI-HS system can be used for the bidirectional optical transmission of SPI signals with transmission rates of up to 1Mbit/s. It consists of two battery supplied transceivers connected to each other with an optical fiber. With the optical transmission of the shielded case and the external filter, the system is well equipped for EMI and EME tests.
