Products
- For immunity test on electronic equipment, buried object identification, wideband jammers
- Up to 41 kV/M at 10m
- Requency Range: 100MHz to 6GHz
The broadband horn antenna BBHA 9120 C is a linear polarized double ridged horn antenna.
- 2 GHz to 18 (20) GHz
- SMA - female
The STLP 9128 E special is nearly identical like the STLP 9120 E but with folded longest elements and smaller structure angle.
- 80 - 1700(2700) MHz
- Type N (female) or Type 7/16 (female)
The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.
The CAR arbitrary waveform generator 6000 is a compact EMC testing system for performing voltage variations on supply lines of vehicles. The system strictly complies with the international standards and manufacturer standards that describe phenomena on the power supply of vehicles. Thus, the CAR arbitrary waveform generator 6000 is the optimal voltage power source for battery simulation up to 70V. It can simulate pulse 2b, pulse 4, starting profile, superimposed alternating voltage, and others, up to a battery current of 100A.
Compact EMC test unit designed for testing electromagnetic immunity of the electrical installation of vehicles and components against supply line transients. PG 2804 includes the generation of pulses #5 / Test A and Test B. It is designed to be connected to the power supply interface of the CAR-TESTER. Load Dump Generator EMC-Test Equipment for the electrical installation of vehicles.
- Puls #5 / Test A / Test B
- Ri = 0.5 / 1 / 2 / 4 / 8 Ω
- Used with CAR-SYS 14 or independently with Coupling Network.
High-Voltage DC Test Sets HTS 20-10 are designed for testing dc dielectric strength of components, insulations, air- and surface flash-over gaps. Also for testing SPDs according to IEC 61643-1. The test voltage can be adjusted from 0.2 kV up to 20 kV. The test voltage rises like a ramp from zero to the selected test voltage. The rate of rise can be adjusted from 100 V/sec up to 10000 V/sec. Then the test voltage remains at the selected value for the test time, which can be adjusted from 1 – 1000 sec. Figure: incl. option PA503
The oscillatory wave generator IPG 2554 has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory waves according to IEC 61000-4-18 requirements. It generates a decaying sine waveform with ringing frequency from 100 kHz to 30.0 MHz. These waveforms represent disturbances occurring in power, control and signal cables installed in high voltage and medium voltage stations and in heavy industrial installations.
The oscillatory wave generator IPG 2553 has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory magnetic field according to IEC 61000-4-10 requirements. It generates a decaying cosine current waveform with ringing frequency of 100 kHz or 1.0 MHz. The generator output is connected to special designed Helmholtz-coil which generates magnetic field with 10 - 100 A/m.
IPG 612T RING-WAVE GENERATOR is a High-voltage pulse generator producing Ring Wave 0.5 µs / 100 kHz acc. to IEC 61000-4-12. The output peak voltage can be preset continuously from 0.2 - 6 kV. Rise time 0.5µs to the first peak, ringing frequency 100 kHz. The picture is shown with PA 503 Option.
