Products
- Low inductive, high precision lead resistors
- For power line and data line
- Software procedure for verification
- High input impedance ≥ 100 G Ohm
- Wide measurement ± 1V ~ 100 kV
- High accuracy and resolution ± 1% ± 2 counts
- Portable with large LCD/LED display 4 ½ Digit LCD
- Battery or AC supply
- Measure DC up to 100kV
The original EMC EPS Bar is white Expanded Polystyrene can optional be painted coating to extend durability. They come in dimensional metric sizes of 100 x 8.5 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Bar is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 4 sides allows for easy positioning and test setups.
The original EMC EPS 70cm Support is white Expanded Polystyrene. They come in dimensional metric sizes of 40 x 60 x 70 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. Since the EMC EPS 70cm Support is made from a denser EPS rating, it is crush resistance and able to withstand heavy weight loads without deforming.
The original EMC EPS Cube is white Expanded Polystyrene can optional a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 10 cm which matches EUT height requirements for IEC testing above the ground plane for IEC 61000-4-5 and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Cube is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.
The optoUSB-3.0 system can be used for the optical transmission of USB signals up to a data rate of 5Gbit/s according to the USB3.0 standard. It can be used to transmit USB signals over long distances (up to 50m) or to handle ground potential problems. With the optical transmission and the shielded case, the system is well equipped for EMI and EME tests.
- optoUSB3.0 USB hub with 2 USB ports (not as EMI robust as 2.0-RBRIR version)
- optoUSB2.0 USB hub with 4 USB ports (not as EMI robust as -RBRIR version)
- optoUSB2.0-RBDIR uses a Rosenberger connector which has been proven to be more EMI robust)
The optoTTL 12-5-u is used for the optical transmission of 12-volt and 5-volt TTL (Transistor-Transistor Logic) digital signals. Up to 16 digital signals with a sampling rate of 40 MS/s (each channel) can be transmitted. The system consists of a transmitter supplied by batteries, a simplex-62,5/125µm-multimode optical cable, and a receiver – which has integrated batteries as well.
- 10 kHz - 3 GHz, 40dB Gain, 5dB N.F.
- Compensation long cable loss for EMI Measurement
- Improve system noise floor flatness
- High EMI performance
- High linearity LNA for EMI measurement
- High dynamic range
- Unconditionally Stable
- State-of-the-Art Technology
- 20 MHz - 3 GHz, 30dB Gain, 5dB N.F.
- Compensation long cable loss for EMI Measurement
- Improve system noise floor flatness
- High EMI performance
- High linearity LNA for EMI measurement
- High dynamic range
- Unconditionally Stable
- State-of-the-Art Technology
The Loop Antenna Stand is an advanced antenna support device designed to meet the demands of diverse signal requirements, featuring three primary functions: elevation adjustment, horizontal/vertical orientation, and a 180-degree rotation capability.
