Standards

EMI Camera for Low Emission / High Field Use

• 30x Optical Zoom
• Low light uses 0,05 lux (day) and 0,005 lux (night)
• Integrated microphone 
• Battery or wall-powered
• Single Fiber operation (duel direction)
• Local controls on back (zoom/pan/tilt/focus/..)
• Options for Pan/Tilt, Joystick, HIRF, recording, motion triggering, OCR, ...

The CAR-PFS-80 is an automotive power fail simulator, which is designed for performing fast voltage dips and drops (micro-interruptions) according to standard requirements, mainly from vehicle manufacturers. The electronic switches in the generator allow switching times below 1 microsecond.

The EPS Test Table is a simple, inexpensive solution for your EMI testing. It is made from durable, expanded polystyrene (EPS) material and can be customized to your requirements. Complies with CISPR, ISO, & IEC requirements for having a low permittivity and can be used for additional standards.

• High strength EPS 3lb per ft³
• Low Permittivity >1.04
• Made for high loading 500 lb.
• Options
• vinyl topper with your company logo (shown in picture)
• epoxy coating for the top (can be combined with vinyl)

The optoCAN-LS system can be used for the bidirectional optical transmission of CAN optical transmitter for low speed-CAN signals with transmission rates of up to 125kbit/s. It consists of two identical battery supplied transceivers connected to each other with an optical fiber. With the optical transmission and the shielded case, the system is well equipped for EMI and EME tests.

The Absolute EMC106 series of cables is a very high-performing Coax operating up to 18GHz with incredibly low losses. It can be used for high-power applications resulting in more power reaching your antenna. Also ideal for emissions testing up to 18GHz. allowing for long-distance runs with less loss. 

The Absolute Coax series of cables are designed specifically to meet the requirements for EMC testing. Each industry has requirements that are unique. EMC is no different. Absolute EMC has gone through the selection process to only offer the best performance quality and value. Taking away the need to spend hours searching and looking through specs and manufacturers to find what you hope is the best value. 4 options are available fitting most EMC applications.

Test System for MIL-STD-641 CS114, CS115, CS116

• Automatic calibration for the whole test frequency range
• Application of all test frequencies automatically. The level can be selected or automatic.
• NO need to manually configure the measurement equipment
• NO need to manually integrate the transfer function of probes and attenuators
• Generation of test reports: NO need to record all values read from the measurement equipment
• Generation of calibration reports: NO need to record all calibration setting parameters
• Rack together and add CS101, CS109, and RS101 (sections 18, 19, and 20 of the RTCA DO-160G are also available.)

The oscillatory wave generator IPG 2554 S has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory waves according to IEC 61000-4-18 requirements. It generates a decaying sine waveform with ringing frequency from 100 kHz and 1 MHz. These are considered the slow waves. These waveforms represent disturbances occurring in power, control, and signal cables installed in high voltage and medium voltage stations and in heavy industrial installations.

Low-Frequency Transmit Coil (CAB4-3912)

• Frequency: 9 kHz to 150 kHz
• Main Diameter: 120 mm
• Maximum Current: 15 A
• Number of turns: 20

Low-Frequency Sense Coil (CABLSLF) 

• Frequency: 9 kHz to 150 kHz
• Diameter to center of the coil: 40 mm
• Number of turns: 51
• Wire type: 7/41 LITZ
• Winding Type: Electrostatically shielded

CABCISPR2532A

• TEST STANDARD: CISPR 25
• 5 μH // 50 Ω LISN / Artificial Network
• Small Size 80 x 80 x 120mm