Standards

Products

FP-COMB 32, Combined Automatic 3-Phase Coupling / Decoupling Network

FP-COMB 32

  • Voltage 480V AC & DC
  • Current 32 AMPs
  • Automatic Switching Surge, EFT, Ringwave
  • IEC & ANSI Coupling

CAB134k Coupling Network for 134kHz

Coupling Network for 134kHz 

  • It matches 50 Ohm amplifier  
  • Use with CAB4-3912 loop antenna
  • Can work with other similar antennas
  • Type N f-n connectors attached directly to loop 

CAB1356m Coupling Network for 13.56 MHz

Coupling Network for 13.56 MHz 

  • It matches 50 Ohm amplifier  
  • Use with CAB4-3910 loop antenna
  • Can work with other similar antennas
  • Type N f-n connectors attached directly to the loop 

SGxxxxG Ground Plane Derivative E/H Probes

  •  Up to 10 GHz – Wideband pulsed field measurement
  •  High Accuracy – Captures fast transients
  •  Passive Operation – No power needed
  •  EMI Immune – Interference-free data
  •  Oscilloscope Ready – Direct coaxial output
  •  Rugged Design – Built for harsh environments

SFExxG & SFGxxG Free Field Derivative E/H Probes

  •  Up to 10 GHz – Wideband pulsed field measurement
  •  High Accuracy – Captures fast transients
  •  Passive Operation – No power needed
  •  EMI Immune – Interference-free data
  •  Oscilloscope Ready – Direct coaxial output
  •  Rugged Design – Built for harsh environments

U-DC Single channel w/multichannel receiver 17Bit, 60V, 10Hz

U-DC

  • High-resolution (16 bit)
  • Measurement Display
  • +/-60V input; +/- 6V or +/-12V output (customizable)
  • Up to 40 samples / s (remote access, moving mean mode, programmable)
  • Multi-channel receiver with Display and remote data access via USB, GPIB,...

Reverb Chamber Retrofit

Any shielded room can be converted to a Reverberation chamber. This is an easy process where Aluminum panels and fixtures are fitters inside the chamber to raise the Q of the chamber. Special precautions are made to make sure all electrical bonding is done so connections do not Oxidize. Stirrers are installed based on customers' requirements. this can be 1, 2. or even more. The use of 2 stirrers perpendicular to each other is recommended but it is up to the user. 

HFRA 5164, 10 kHz - 120 MHz Transmitting loop antenna

  • The circular transmitting loop antenna
  • 0.01 - 120 MHz
  • diam. 100 mm
  • turns 3
  • BNC Connectors 

ESD Test Table Kit

The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.

STLP 9129 - 70 MHz - 10 GHz Stacked Log. Periodic Antenna

The STLP 9129 was specially designed for wideband immunity tests. This unrivaled bandwidth was achieved by combining both well-proven antenna designs STLP 9128 D and the STLP 9149. The STLP 9129 does provide the optimum out of gain and field uniformity at the same time as well as both basic antennas do. Main Application: Generation of defined high field strength levels for radiated immunity testing acc. IEC 61000-4-3.

  • 70 MHz to 10 GHz
  • gain of 8.6 dBi, ripple of less than +/- 2.3 dB
  • Type N female or Type 7/16 female


Loading...