Standards

DGA 9553 BNC is a bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions.

There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration, an attenuator directly at the pulse generator output is inevitable.

• 3, 6, 10, 20, and 30 dB Values available
• 50 Ohm, Low VSWR
• 1 Watts

This generator has been designed as a trigger source for Marx generators and for trigatrons (triggered spark gaps). It can replace the obsolete PT55 trigger generator as mechanical dimensions and attachment points are the same. The advantages of our generator are:

• · Solid-state switch
• · High repetition rate
• · Long lifetime
• · No need of gas
• · No need of external high voltage power supply
• · Can be triggered by a 5 V digital signal or by fiber optic

• Shorter version of the PPL200-70-S 
• 270 x 100 x 76 cm (L x W x H)
• For an immunity test on small and medium-sized devices
• For immunity tests on automotive devices  according  to  the European  directive  2004/104/EC 
• Requency Range: 10kHz to 30MHz
  
  

The optoUART system can be used for the optical transmission of UART-signals up to a data rate of 1 Mbit/s.

It can be used to transmit UART-signals over long distances or to handle ground potential problems. With the optical transmission and the shielded case, the system is well equipped for EMI and EME tests.

Linear polarized Stacked Logarithmic Periodic Broadband Antenna with N- or 7/16connector for Receive and Transmit Applications. Main Application: Generation of defined field strength levels for radiated immunity testing. Further the cross-polar rejection of the STLP 9128 F is excellent.

• 70 MHz to 1.5 GHz
• gain of 8.6 dBi, ripple of less than +/- 2.3 dB
• Type N female or Type 7/16 female

Broad-Band Horn Antenna

• 15 - 26.5 (40) GHz
• SMA-compatible connector

The LSProbe 1.2 Variant E Field Probe is a high-speed, high-accuracy, and high-dynamic range electric-Field probe.

• Its standard frequency range of 10 kHz – 8.2 GHz. 1,000 V/m
• Best-in-class compensation of linearity, frequency, and temperature guarantees accurate measurements from less than 0.1 to at least 1,000 V/m.
• A dynamic range of 100 dB is achieved for many frequencies, enabling Field measurements at more than 10,000 V/m.
• Customized high Field-strength „X“-variants, supporting up to 30,000 V/m and a damage level of 100,000 V/m, are available upon request.

Gtemcell offers an innovative shielding product made of a highly conductive double layer of aluminum with internal reinforcing mesh in polyester for the coating and creation of shielded environments within pre-existing structures.  The application frequencies range from a few Mega Hertz to several GHz with an electric field attenuation of 45-80dB. The great advantage is ease of application even on curved and complex surfaces and lower costs which make this application particularly attractive. GTEMCELL supplies the shielded fabric or performs all the environmental shielding work. The aesthetic finishes are the responsibility of the customer.
The construction includes a preliminary inspection to evaluate all the "critical" aspects such as the openings present: doors. windows, air conditioning systems, electrical connections and consequently draw up an economic evaluation of the costs.

The Conformity Assessment Business Model DCS12 Test Generator meets all the DCS12 wave verification parameters for testing DC, single and three-phase equipment, that is source impedance and verification of damping and frequency when measured into a 10 Ω load. Output amplitude is software adjustable with permanent memory, should re-alignment be needed during calibration. 

• There are three fixed outputs: 600 V, 750 V, and 2500 V
• 15.9 kHz ±10 %
• 10.9 kHz ±10 %

The Conformity Assessment Business Model DCS06 Test Generator has been designed to operate with its complementary injection clamp to fully meet the pulse requirements of DCS06 when tested into a 5? load. It operates from an intuitive touch screen interface and has full phase synchronization up to 800 Hz input frequency with 1-degree steps. It has been designed with future revisions of the test standard in mind.