Products
The oscillatory wave generator IPG 2554 S has been designed for immunity testing of electrical and electronic equipment against repetitive damped oscillatory waves according to IEC 61000-4-18 requirements. It generates a decaying sine waveform with ringing frequency from 100 kHz and 1 MHz. These are considered the slow waves. These waveforms represent disturbances occurring in power, control, and signal cables installed in high voltage and medium voltage stations and in heavy industrial installations.
20 mH current-compensated inductors for symmetrical signal-line testing.
The Haefely DEC 5 separates auxiliary equipment from an EUT during transient immunity testing on unshielded symmetrical lines. It supports up to four wires and impulses up to 6.6 kV, using 20 mh current-compensated inductors; two inductors with two coils each. Coupling is performed by a separate network, allowing protection and decoupling to match the signal circuit.
Surge coupling for unbalanced lines, plus ring-wave coupling for balanced and unbalanced lines.
The Haefely PCD 126A couples combination-wave surge and 100 kHz ring-wave disturbances onto up to four unshielded data or control wires at 6.6 kV peak. Combination-wave testing is for asymmetrical lines; ring-wave testing supports both symmetrical and asymmetrical lines. Coupling elements and paths are selected manually, with decoupling supplied separately.
U-DC
- High-resolution (16 bit)
- Measurement Display
- +/-60V input; +/- 6V or +/-12V output (customizable)
- Up to 40 samples / s (remote access, moving mean mode, programmable)
- Multi-channel receiver with Display and remote data access via USB, GPIB,...
- The circular transmitting loop antenna
- 0.01 - 120 MHz
- diam. 100 mm
- turns 3
- BNC Connectors
The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.
The STLP 9129 was specially designed for wideband immunity tests. This unrivaled bandwidth was achieved by combining both well-proven antenna designs STLP 9128 D and the STLP 9149. The STLP 9129 does provide the optimum out of gain and field uniformity at the same time as well as both basic antennas do. Main Application: Generation of defined high field strength levels for radiated immunity testing acc. IEC 61000-4-3.
- 70 MHz to 10 GHz
- gain of 8.6 dBi, ripple of less than +/- 2.3 dB
- Type N female or Type 7/16 female
The EMC test system is designed for testing electromagnetic immunity of the electrical installation of vehicles and components against supply line transients. EMC - Test Equipment for the electrical installation of vehicles.
- Pulse #1 1-5/2000us, 600 V
- #1 1-5/1000us, 600 V
- Pulse #2a 1 / 50us, 600 V
- Pulse #3 5/100 ns, 800 V
NEMP050 Radiated Susceptibility Test System
- Compliance: Meets MIL-STD-461 RS105 standards for NEMP testing.
- High Precision: Generates a minimum electric field of 50 kV/m, with higher fields available for smaller devices.
- Portable Design: Tabletop Easy-to-move frame and compact setup for versatile placement.
- User-Friendly: Controlled via computer with RS232 and USB interfaces.
- Versatile Testing: Ideal for assessing small electronics like printed circuit boards and subsystems.
- Robust Specifications: Quick rise time of 2.3 ns and pulse length of 23 ns, ensuring accurate and reliable results.
Highly Accurate Antenna for Exposure evaluation next to mobile communication facilities e.g. GSM and UMTS base stations Accurate RF radiation safety measurements e.g. nearby broadcast stations or in buildings
