Standards

Products

EMC001330, 10 kHz - 3 GHz, 30dB gain, Low Noise Preamplifier

  • 10 kHz - 3 GHz, 30dB Gain, 6dB N.F.
  • Compensation long cable loss for EMI Measurement
  • Improve system noise floor flatness
  • High EMI performance
  • High linearity LNA for EMI measurement
  • High dynamic range
  • Unconditionally Stable
  • State-of-the-Art Technology

ABSOLUTE EMC TP-Ball Head For Tripod or Monopole

The ABSOLUTE EMC TP-Ball Head is designed to mount a camera or other lightweight item with complete position control. Constructed of PLA plastic, only the 1/4"-20 screw is metal. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

ABSOLUTE EMC TP-Cable Support For Tripod or Monopole

The ABSOLUTE EMC TP-Cable Support is designed to hold wires, Coax, or waveguide parallel to the ground. This is useful in some cases for test setups where the antenna cable needs to be held back and away from the test area. Or in cases where EUT wires can not bend and need to be held up off the floor. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps to tie down cables or a 1m EPS bar. This rugged cable tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

ABSOLUTE EMC TP-Item Tray For Tripod or Monopole

The ABSOLUTE EMC TP-Item Tray is designed for holding items up. There is often a need to elevate an item at a specific height. Or, in cases where an antenna or transducer does not have ideal mounting, the tray can hold the item with velcro straps or zip ties. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps. This rugged Item tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

ABSOLUTE EMC MP-Rotator For Tripod or Monopole

The ABSOLUTE EMC MP-Rotator is attached to a 1" Wood Dowel or tube. It holds a second Dowel/tube that can be rotated 360deg to reach out over an obstacle such as a table. This gives the ability to position a camera or other measurement device over top of a test table or in positions where the base/feet of the EMC Monopole/tripod prohibit easy positioning. Constructed of PLA plastic and includes a 36" Hard Wood Dowel. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

ABSOLUTE EMC Custom Antenna Adaptors For Tripod or Monopole

The ABSOLUTE EMC can design and produce Custom Antenna Adaptors. each adaptor is mad for your antennas and tripods or to be used on our Absolute EMC Tripod/monopod stands. Adaptors can be designed to rotate the antenna in the center from horizontal to vertical and position it at the center of gravity of the antenna so it sits easily on the antenna stand. Cost is set based on the size and complexity of the adaptor. 

1-2, 2-4, and 4-6 GHz, Array Horn Antennas for HiRF Levels CAT L

Absolute EMC with strategic partners is offing Antenna Arrays for meeting the high demanding levels required by DO-160 CAT L and MIL-STD-464. Testing for HiRF High Intens Radio Fields up to and exceeding 7200 V/m with commercially available TWT Pulsed or Solid-state amplifiers. Antennas can also be used for HERO testing of MIL-STD-464 System-level requirements. 

  • 1-2 GHz Gain @ 1m, 22.7 - 23.5 dBi Min
  • 2-4 GHz Gain @ 1m, 24 dBi
  • 4-6 GHz Gain @ 1m, 26 dBi

0.4-1, 1-1.5, and 1.5 - 2.6, Array Horns Antennas for HiRF Levels CAT K

Absolute EMC with strategic partners is offing Antenna Arrays for meeting the high demanding levels required by DO-160 CAT K and MIL-STD-464. Testing for HiRF High Intens Radio Fields up to and exceeding 5000 V/m with commercially available TWT Pulsed or Solid-state amplifiers. Antennas can also be used for HERO testing of MIL-STD-464 System-level requirements. 

  • 400 - 1000 MHz Gain @ 1m, 11.6-15.8 dBi
  • 1 - 1.6 GHz Gain @ 1m, 18.9 - 20.6 dBi
  • 1.5 - 2.6 GHz Gain @ 1m, 20.3 - 22 dBi

2-3.2, 2.6-4, 4-6, Lens Horns Antennas for HiRF Levels CAT K

Absolute EMC with strategic partners is offing Lens Antenna for meeting the high demanding levels required by DO-160 CAT K and MIL-STD-464. Testing for HiRF High Intens Radio Fields up to and exceeding 5000 V/m with commercially available TWT Pulsed or Solid-state amplifiers. Antennas can also be used for HERO testing of MIL-STD-464 System-level requirements. Lens Antennas focus the field to reach higher levels in the near-field.

  • 2 - 3.2 GHz Gain @ 1m, 20.0 - 20.9 dBi
  • 2.6 - 4 GHz Gain @ 1m, 20.2 - 22.8 dBi
  • 4 - 6 GHz Gain @ 1m, 21.1 - 23.6 dBi

6-8.2, 8-12.4, 12.4-18, High Gain Horn Antennas for HiRF Levels CAT K

Absolute EMC with strategic partners is offing high gain HiRF Antennas for meeting the high demanding levels required by DO-160 CAT K and MIL-STD-464. Testing for HiRF High Intens Radio Fields up to and exceeding 5000 V/m with commercially available TWT Pulsed or Solid-state amplifiers. Antennas can also be used for HERO testing of MIL-STD-464 System-level requirements. 

  • 6 - 8.2 GHz Gain @ 1m, 21.8 - 23.1 dBi
  • 8 - 12.4 GHz Gain @ 1m, 20.7 - 23.3 dBi
  • 12.4 - 18 GHz Gain @ 1m, 21.6 - 23.2 dBi


Loading...