Langer P12t set | Triggered Mini Burst Magnetic Coupling Generator

Approx. 1 mT | Coupling-clamp tip | 5 V TTL SMB trigger | Single pulse to 10 kHz | 3 us delay

P12t combines TTL-synchronized magnetic disturbance generation with a tip that uses the coupling-clamp principle. It is intended for detailed susceptibility analysis while a circuit is in a specific operating condition. Use a DUT signal or external logic as the trigger and compare the failure response as the source position or circuit design changes. The set includes cable, power supply, case and manual.

P12t set - Datasheet

SPECIFICATIONS

P12t set - Triggered Mini Burst Magnetic Coupling Generator

P12t combines TTL-synchronized magnetic disturbance generation with a tip that uses the coupling-clamp principle. It is intended for detailed susceptibility analysis while a circuit is in a specific operating condition. Use a DUT signal or external logic as the trigger and compare the failure response as the source position or circuit design changes. The set includes cable, power supply, case and manual.

P12t set, Mini Burst Field Generator (B, Trigger)

Features and application benefits

FeatureEngineering benefit / use
Coupling geometry The P12t tip follows the coupling-clamp principle, distinguishing it from P11t even though their headline electrical values match.
Synchronization Use the 5 V TTL SMB input to synchronize magnetic disturbances with DUT activity or external logic.
Timing The published trigger delay is 3 us and the frequency range is single pulse to 10 kHz.

Technical specifications

ParameterSpecification
External trigger input SMB, male, jack; 5 V TTL
Generated magnetic flux density ca. 1 mT
Pulse parameter / Frequency single ... 10 kHz
Pulse parameter / Trigger-pulse delay 3 us
Pulse parameter / Supply voltage 6.5 V ... 15 V

Included components

PhotoQty.ItemFunction / key specifications
P12t, Mini Burst Field Generator (B, Trigger) 1x P12t Mini Burst Field Generator (B, Trigger)
Generator voltage: 400 V
External trigger input: SMB, male, jack; 5 V TTL
Generated magnetic flux density: ca. 1 mT
Pulse parameter / Pulse width: 2 ns ... 8 ns
SMB-BNC 1 m, SMB-BNC Measurement Cable 1x SMB-BNC 1 m SMB-BNC Measurement Cable
Weight: 25 g
Sizes (L x W x H): 1 m
  1x NT FRI EU Power Supply Unit
  1x P12t case System Case
  1x P12t m P12t Set User Manual

Included component specifications

ComponentParameterSpecification
P12t Generator voltage 400 V
P12t External trigger input SMB, male, jack; 5 V TTL
P12t Generated magnetic flux density ca. 1 mT
P12t Pulse parameter / Pulse width 2 ns ... 8 ns
P12t Pulse parameter / Frequency single ... 10 kHz
P12t Pulse parameter / Polarity switchable
P12t Pulse parameter / Trigger-pulse delay 3 us
P12t Pulse parameter / Supply voltage 6.5 V - 15 V
P12t Pulse parameter / Current input 50 mA @ 6.5 V
P12t Pulse parameter / Weight 20 g
P12t Pulse parameter / Sizes (L x W x H) (125 x 24 x 20) mm
SMB-BNC 1 m Weight 25 g
SMB-BNC 1 m Sizes (L x W x H) 1 m

System requirements and ordering notes

6.5-15 V supply; power supply included. A powered DUT and a way to observe its functional response are required. The tools support engineering diagnosis; they do not replace the complete standardized compliance test setup.

Datasheets

DocumentPDF
P12t set - Datasheet View PDF

Practical questions

QuestionAnswer
What is this product best suited to? Choose the clamp-principle tip for a targeted magnetic coupling task.
What supporting equipment is needed? 6.5-15 V supply; power supply included. A powered DUT and a way to observe its functional response are required. The tools support engineering diagnosis; they do not replace the complete standardized compliance test setup.
Does this establish compliance with IEC 61000-4-4 or IEC 61000-4-2? These are development and diagnostic tools. Relating a local disturbance to an EFT/burst or ESD failure helps troubleshooting; formal compliance requires the applicable standardized generator, coupling method, test setup and procedure.

PCB immunity selection guide

Compare generation, coupling and detection tools. The kit pictures identify the complete sets. Product links below use the planned Absolute EMC product pages.

KitProduct / functionKey distinctionRequired pulse source / power
E1 set, Immunity Development System E1 set
Integrated generation and local E/H-field troubleshooting
Approx. 0-1500 V pulses | 2 ns rise / 10 ns tail | 4 H-field + 5 E-field sources | 10 Mbps optical sensor SGZ 21 included; 12 V / 200 mA
E2 set, TS 23 Immunity Development System E2 set
Programmable pulse generation and differential injection
Up to 2.2 kV adjustable | 1.5 ns rise | Adjustable 1.5 kHz repetition | Both polarities | 50 Mbps optical sensor TS 23 included; 24 V / 1 A DC
S2 set, Magnetic Field Probes for E1 S2 set
Transient magnetic-field sensing
Active + passive H-field probes | 3 MSA 02 heads | Optical signal transfer | MSA 02: 1 AAA battery SGZ 21 receiver documented; confirm E2 receiver arrangement
P1 set, Mini Burst Field Generators P1 set
Battery-powered E/H-field injection
3 generators: P11 + P12 + P21 | Approx. 1 mT H-field / 100 kV/m E-field | Single pulse or 5 kHz | 1.5 V AAA 1.5 V AAA supply; single pulse / 5 kHz
P23 set, Mini Burst Field Generator (E) P23 set
Fine-tip capacitive pulse injection
1.2 kV generator voltage | 10 pF coupling | 1.8-10 ns rise | Single pulse or 5 kHz | 1.5 V AAA 1.5 V AAA supply; single pulse / 5 kHz
P11t set, Mini Burst Field Generator (B, Trigger) P11t set
TTL-synchronized magnetic pulse injection
Approx. 1 mT | 5 V TTL SMB trigger | Single pulse to 10 kHz | 3 us trigger delay | 6.5-15 V supply 6.5-15 V supply; power supply included
P12t set, Mini Burst Field Generator (B, Trigger) P12t set
TTL-synchronized clamp-style magnetic coupling
Approx. 1 mT | Coupling-clamp tip | 5 V TTL SMB trigger | Single pulse to 10 kHz | 3 us delay 6.5-15 V supply; power supply included
H2 set, Field Sources H2 set
External-generator E/H-field coupling
6 field sources: 3 H + 3 E | Up to 4.4 kV source supply | External EFT/burst generator required External EFT/burst generator; source limit 4.4 kV
H3 set, Field Sources H3 set
Extended external-generator E/H-field coupling
9 field sources: 4 H + 5 E | High-voltage SMB connections | SHV or Fischer cable choice | External generator required External EFT/burst generator; observe each source rating
PT4 set, EFT Generator Set PT4 set
Potential-free pulse injection plus E/H-field coupling
4.5 kV maximum burst input | 1:1 transformer | 500 V output dielectric strength | H- and E-field sources External EFT/burst generator; transformer maximum 4.5 kV
H4-IC set, EFT/Burst Magnetic Field Source H4-IC set
Small-area magnetic field coupling
Up to 200 mT | 2.54 mm2 resolution | 1.8 mm diameter head | 0-66 MHz | 4 kV maximum burst External EFT/burst generator; 4 kV maximum burst input
H5-IC set, EFT/Burst Magnetic Field Source H5-IC set
Magnetic field coupling with BS 06DU-s
Up to 150 mT | 5 x 6 mm head | 0-560 MHz | 4 kV maximum burst | 15 g source External EFT/burst generator; 4 kV maximum burst input
BD 11, H-Field Burst Detector BD 11
Cable-transient detection and event indication
Adjustable sensitivity | LED + relay + optical outputs | 20 m maximum fiber | 2 AAA batteries | 88 x 85 x 32 mm Two 1.5 V AAA batteries
OTHER PRODUCTS IN THE SAME CATEGORY:
Loading...