Langer A200 Analog Optical Fiber Probes | DC to 500 kHz

DC to 500 kHz | 1 or 2 analog channels | 3 Msps / 12 bit | 0 to 10 V / 0 to 50 V

Langer A200 optical fiber probe sets monitor DUT waveforms during EFT, ESD and RF immunity testing. The included sensor and receiver transmit signals over fiber for display on an oscilloscope. Choose one channel with 1.5 m fiber or two channels with two 6 m fibers. Supported fiber length is 1 to 20 m.

A200-1 Set - Absolute EMC Datasheet

A200-2 Set - Absolute EMC Datasheet

SPECIFICATIONS

A200 Analog Optical Fiber Probes | DC to 500 kHz

Monitor analog voltages inside the device under test while keeping the signal transmission path optical. Select the channel count for the number of signals to observe, then match the sensor range and bandwidth to the waveform.

Choose a configuration

KitVersionChannelsIncluded fiber
A200-1 set A200-1 set 1 1 x 1.5 m
A200-2 set A200-2 set 2 2 x 6 m

Shared technical specifications

The following sensor and receiver specifications apply to both channel configurations.

ComponentParameterSpecification
System Bandwidth DC ... 500 kHz
System Sampling rate 3 Msps
System Resolution 12 Bit
AE 200 Optical Receiver Bandwidth DC ... 500 kHz
AE 200 Optical Receiver Voltage range - output 0 V ... 10 V
AE 200 Optical Receiver Optical input: Optical fiber Ø 2.2 mm
AE 200 Optical Receiver Supply voltage 12 V ... 16 V
AE 200 Optical Receiver Current input ≈ 100 mA
AS 200 Optical Sensor Bandwidth DC ... 500 kHz
AS 200 Optical Sensor Measuring range 0 V ... 50 V / 0 V ... 10 V DC (switchable)
AS 200 Optical Sensor Input resistance 100 k?
AS 200 Optical Sensor Radiated immunity > 100 V/m
AS 200 Optical Sensor Supply voltage 3 V ... 16 V
AS 200 Optical Sensor Current input ≈ 30 mA
AS 200 Optical Sensor Optical fibre length 1 m ... 20 m

Included components

PhotoItemA200-1 setA200-2 set
AE 200, Optical Receiver AE 200, Optical Receiver 1x 2x
AS 200, Optical Sensor (50 / 10) V DC AS 200, Optical Sensor (50 / 10) V DC 1x 2x
LWL optical fiber, diameter 2.2 mm LWL optical fiber, diameter 2.2 mm 1x (1.5 m) 2x (6 m each)
NT FRI EU, Power Supply Unit NT FRI EU, Power Supply Unit 1x 1x
Connection accessory tapeConnection sockets Connection accessories 1x 1x
  System case 1x 1x
  Analog m, User Manual 1x 1x

Measurement setup

Connect the sensor at the DUT and send its signal through the optical fiber to the receiver. Connect the receiver output to the oscilloscope and supply each module at its specified voltage.

Application with Set AS200
Application with Set AS200

Optical signal transmission for EMC testing

Datasheets

Compare all Langer optical signal transmission sets

KitModelSignalChannels / directionBandwidth / data rateSampling / functionSupported fiber lengthIncluded fiber
A100-1 set A100-1 set Analog 1 DC to 25 kHz 125 ksps / 12 bit 1 to 20 m 1.5 m
A100-2 set A100-2 set Analog 2 DC to 25 kHz 125 ksps / 12 bit 1 to 20 m 2 x 6 m
A200-1 set A200-1 set Analog 1 DC to 500 kHz 3 Msps / 12 bit 1 to 20 m 1.5 m
A200-2 set A200-2 set Analog 2 DC to 500 kHz 3 Msps / 12 bit 1 to 20 m 2 x 6 m
A300-1 set A300-1 set Analog 1 DC to 5 MHz 12.5 Msps / 10 bit 1 to 20 m 1.5 m
A300-2 set A300-2 set Analog 2 DC to 5 MHz 12.5 Msps / 10 bit 1 to 20 m 2 x 6 m
OSE 150-1 set OSE 150-1 set Digital 1 DC to 50 Mbps Logic transmission 1 to 20 m 1.5 m
OSE 150-2 set OSE 150-2 set Digital 2 DC to 50 Mbps Logic transmission 1 to 20 m 2 x 6 m
OSE 450 set OSE 450 set Digital 4 DC to 50 Mbps Logic transmission See receiver / sensor configuration 4 x 6 m
CAN 100 set CAN 100 set CAN Bidirectional Up to 1 Mbit/s High-speed CAN 10 m maximum; 6 m at 1 Mbit/s Double 10 m
LIN 100 set LIN 100 set LIN Bidirectional LIN bus Master / slave Up to 20 m Double 10 m
OB 100 set OB 100 set CAN / LIN Bidirectional CAN / LIN selectable 2 Opto-Boxes 20 m; 6 m at 1 Mbit/s CAN Double 10 m
OTHER PRODUCTS IN THE SAME CATEGORY:
Loading...