Langer A100 Analog Optical Fiber Probes | DC to 25 kHz

DC to 25 kHz | 1 or 2 analog channels | 125 ksps / 12 bit | 0 to 10 V / 0 to 50 V

Langer A100 optical fiber probe sets monitor DUT waveforms during EFT, ESD and RF immunity testing. The included sensor and receiver transmit signals over fiber for display on an oscilloscope. Choose one channel with 1.5 m fiber or two channels with two 6 m fibers. Supported fiber length is 1 to 20 m.

A100-1 Set - Absolute EMC Datasheet

A100-2 Set - Absolute EMC Datasheet

SPECIFICATIONS

A100 Analog Optical Fiber Probes | DC to 25 kHz

Monitor analog voltages inside the device under test while keeping the signal transmission path optical. Select the channel count for the number of signals to observe, then match the sensor range and bandwidth to the waveform.

Choose a configuration

KitVersionChannelsIncluded fiber
A100-1 set A100-1 set 1 1 x 1.5 m
A100-2 set A100-2 set 2 2 x 6 m

Shared technical specifications

The following sensor and receiver specifications apply to both channel configurations.

ComponentParameterSpecification
System Bandwidth DC ... 25 kHz
System Sampling rate 125 ksps
System Resolution 12 Bit
AE 100 Optical Receiver Bandwidth DC ... 25 kHz
AE 100 Optical Receiver Optical input: Optical fiber Ø 2.2 mm
AE 100 Optical Receiver Voltage range - output 0 V ... 10 V
AE 100 Optical Receiver Supply voltage 12 V ... 16 V
AE 100 Optical Receiver Current input ≈ 30 mA
AE 100 Optical Receiver Connector - output BNC
AS 100 Optical Sensor Bandwidth DC ... 25 kHz
AS 100 Optical Sensor Sampling rate 125 ksps
AS 100 Optical Sensor Measuring range 0 V ... 50 V / 0 V ... 10 V DC (switchable)
AS 100 Optical Sensor Input resistance 100 k?
AS 100 Optical Sensor Radiated immunity > 200 V/m
AS 100 Optical Sensor Supply voltage 3 V ... 16 V
AS 100 Optical Sensor Current input ≈ 3 mA
AS 100 Optical Sensor Optical fibre length 1 m ... 20 m

Included components

PhotoItemA100-1 setA100-2 set
AE 100, Optical Receiver AE 100, Optical Receiver 1x 2x
AS 100, Optical Sensor (50 / 10) V DC AS 100, Optical Sensor (50 / 10) V DC 1x 2x
LWL optical fiber, diameter 2.2 mm LWL optical fiber, diameter 2.2 mm 1x (1.5 m) 2x (6 m each)
NT FRI EU, Power Supply Unit NT FRI EU, Power Supply Unit 1x 1x
Connection accessory tapeConnection sockets Connection accessories 1 tape + 3 connection sockets 1 tape + 6 connection sockets
  System case 1x 1x
  Analog m, User Manual 1x 1x

Recommended sensors and compatible systems

Specify the sensor when requesting a quote. Check the receiver family and signal range when configuring an alternative to the standard included sensor.

PhotoSensorCompatible systemBandwidthMeasuring rangeInput resistanceSupply
AS 110 optical sensor AS 110 A100 / AE 100 DC ... 25 kHz 0 V ... 10 V / 0 V ... 1 V DC (switchable) 1 M? 3 V ... 16 V
AS 120 optical sensor AS 120 A100 / AE 100 10 Hz ... 25 kHz 0.1 V ... 1 V AC (switchable) 1 M? 3 V ... 16 V

Measurement setup

Connect the sensor at the DUT and send its signal through the optical fiber to the receiver. Connect the receiver output to the oscilloscope and supply each module at its specified voltage.

Application with Set A100 and field source
Application with Set A100 and field source

Optical signal transmission for EMC testing

Datasheets

Compare all Langer optical signal transmission sets

KitModelSignalChannels / directionBandwidth / data rateSampling / functionSupported fiber lengthIncluded fiber
A100-1 set A100-1 set Analog 1 DC to 25 kHz 125 ksps / 12 bit 1 to 20 m 1.5 m
A100-2 set A100-2 set Analog 2 DC to 25 kHz 125 ksps / 12 bit 1 to 20 m 2 x 6 m
A200-1 set A200-1 set Analog 1 DC to 500 kHz 3 Msps / 12 bit 1 to 20 m 1.5 m
A200-2 set A200-2 set Analog 2 DC to 500 kHz 3 Msps / 12 bit 1 to 20 m 2 x 6 m
A300-1 set A300-1 set Analog 1 DC to 5 MHz 12.5 Msps / 10 bit 1 to 20 m 1.5 m
A300-2 set A300-2 set Analog 2 DC to 5 MHz 12.5 Msps / 10 bit 1 to 20 m 2 x 6 m
OSE 150-1 set OSE 150-1 set Digital 1 DC to 50 Mbps Logic transmission 1 to 20 m 1.5 m
OSE 150-2 set OSE 150-2 set Digital 2 DC to 50 Mbps Logic transmission 1 to 20 m 2 x 6 m
OSE 450 set OSE 450 set Digital 4 DC to 50 Mbps Logic transmission See receiver / sensor configuration 4 x 6 m
CAN 100 set CAN 100 set CAN Bidirectional Up to 1 Mbit/s High-speed CAN 10 m maximum; 6 m at 1 Mbit/s Double 10 m
LIN 100 set LIN 100 set LIN Bidirectional LIN bus Master / slave Up to 20 m Double 10 m
OB 100 set OB 100 set CAN / LIN Bidirectional CAN / LIN selectable 2 Opto-Boxes 20 m; 6 m at 1 Mbit/s CAN Double 10 m
OTHER PRODUCTS IN THE SAME CATEGORY:
Loading...