EMI Receiver

EMI Measurements:

• FFT-based dual-channel receiver
• According to CISPR16-1-1
• Peak, Quasi-Peak, and Average Detectors
• Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
• The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)

EMI Measurements:

• FFT-based dual-channel receiver
• According to CISPR16-1-1
• Peak, Quasi-Peak, and Average Detectors
• Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
• The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)

EMI Measurements:

• FFT-based dual-channel receiver
• According to CISPR16-1-1
• Peak, Quasi-Peak, and Average Detectors
• Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
• The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)
• Measure 4 lines of 3 phase LISN
• The picture is shown with internal LISN [EMSCOPE RX4 LZ2]

" An RF Probe Kit on Steroids"

• Fully integrated with Y.I.C. Technologies EMViewer software and EMProbe
• Normalization and correction when using the EMViewer software
• Flat response within the range of operation
• Slim Design and Protective Coating
• 18GHz Measured Cable included
• Lectures & Explanation Document
• Designed By Prof. Arturo Mediano, University of Zaragoza, Spain

150 kHz to 6 GHz | Internal spectrum analyzer | 1,218-probe array

EMScanner+ helps engineers locate and compare PCB emission sources across a 316 x 218 mm scan area. A fixed array of 1,218 magnetic-field probes gives fast coverage, with 7.5 mm physical spacing and a manufacturer-stated 3.75 mm effective resolution. The internal spectrum analyzer simplifies the measurement setup; a user PC runs EMViewer.

150 kHz to 6 GHz | Internal spectrum analyzer | Down to 0.06 mm

EMScannerR+ helps engineers locate and compare PCB emission sources across a 316 x 218 mm scan area. Its eight selectable resolution levels run from 7.5 mm down to 0.06 mm for detailed investigation of dense boards. The internal spectrum analyzer simplifies the measurement setup; a user PC runs EMViewer.

150 kHz to 8 GHz | External spectrum analyzer | 1,218-probe array

EMScanner helps engineers locate and compare PCB emission sources across a 316 x 218 mm scan area. A fixed array of 1,218 magnetic-field probes gives fast coverage, with 7.5 mm physical spacing and a manufacturer-stated 3.75 mm effective resolution. Use it with a compatible external spectrum analyzer and a PC running EMViewer.

6 axes | 450 mm radius | 0.01 mm positioning repeatability

EMProbe DBM E6 combines a six-axis robotic arm, near-field probes and EMViewer for repeatable component-side EMI investigations. The dedicated E6 datasheet specifies a 450 mm scan radius, scan spacing down to 0.1 mm and 0.01 mm positioning repeatability. Select the probe and compatible external analyzer to match the emissions and geometry being investigated.

150 kHz to 8 GHz | External spectrum analyzer | Down to 0.06 mm

EMScannerR helps engineers locate and compare PCB emission sources across a 316 x 218 mm scan area. Its eight selectable resolution levels run from 7.5 mm down to 0.06 mm for detailed investigation of dense boards. Use it with a compatible external spectrum analyzer and a PC running EMViewer.

Component-side scanning | Adjustable probe height | External analyzer

EMProbe automates a handheld near-field probe over the component side of a PCB or around a non-flat assembly. Program scan height and position in EMViewer, then acquire RF measurements with a compatible external spectrum analyzer. The compact arm is suited to repeatable bench investigations, with larger arm or extension configurations available for application-specific work.

5 E/H-field probes | Camera tracking | Live EMI visualization

NFP Kit adds camera-based position tracking to handheld near-field measurements. EMViewer recognizes the probe and measurement location from visible markers, helping engineers map emission sources while moving the probe by hand. The kit combines five electric/magnetic probes, a camera, mounting arm and measurement software with your compatible spectrum analyzer.

• Frequency Range of 300 MHz to 6.0 GHz
• Far-Field Patterns and Bisections, including EIRP / TRP / PRD, Circular and linear polarization, and axial ratio patterns
• Near-field insights such as Amplitude and Phase distribution are available in  seconds
• Gain, Efficiency, and S11 chart with Supported VNAs
• “Real-time” real-fast
• Can be used to evaluate either standalone (i.e. passive) antennas or antennas that are embedded in wireless devices (i.e. active antennas). 
• Simple set up and Easy to use