Transient Generator

• Advanced Ripple Testing: Meets ISO 21498, LV123, VW 80300, Nissan MES PW 67602, Mazda, and emerging standards.
• Series Amplifier Integration: High accuracy ripple injection, minimal distortion, and enhanced safety.
• Waveform Versatility: Sine, square, trapezoidal, pulses, and triangle waveform generation.
• WaveMaster Software: Fast DUT impedance measurement, automated test sequences, and dynamic voltage/current control.
• High Power Capability: Ripple Voltage up to 100 Vpp, currents from 100A to 2000A+, and frequency range 10 Hz–300+ kHz.
• Future-Proof Design: Modular architecture for easy upgrades and adaptation to new standards.

• High current power stage (uni-directional)
• Up to 32 channels for switching low-current signals (bi-directional)
• Switching of resistive, inductive, capacitive passive, and active loads/devices
• Input voltage up to 100V
• Output current up to 200A DC

WaveMaster + AnyWave

BOLAB WaveMaster software and the BOLAB AnyWave control unit allow the control of power supplies as well as 4 quadrant amplifiers via the analog interfaces.

The powerful and easy-to-use BOLAB WaveMaster software is unique in the world. Without any knowledge in software development, designing ordinary and complex waveforms is very easy. A graphic waveform editor allows the generation

of individual curves in no time. Also, with tabular input, all types of waveforms can be produced instantly.

WaveMaster + AnyWave

BOLAB WaveMaster software and the BOLAB AnyWave control unit allow the control of power supplies as well as 4 quadrant amplifiers via the analog interfaces.

The powerful and easy-to-use BOLAB WaveMaster software is unique in the world. Without any knowledge in software development, designing ordinary and complex waveforms is very easy. A graphic waveform editor allows the generation

of individual curves in no time. Also, with tabular input, all types of waveforms can be produced instantly.

• Full Compliance – Meets all ISO 7637-4 test requirements
• Pulse A Testing – Simulates MOSFET/IGBT switching noise (100 kHz – 10 MHz)
• Pulse B Testing – Low-frequency sinusoidal disturbances (3 kHz – 300 kHz)
• High-Power RF Amplifier – 75W output (100 kHz – 400 MHz) for clean signal generation
• Burst Generator – Supports configurable burst parameters (1–1000 cycles)
• Power Meter & Directional Coupler – Accurate transient measurement (100 kHz – 10 MHz)
• Integrated Transformer – Isolates high-voltage circuits & prevents transient damage
• Scalable & Modular – Configurable for custom DUT testing needs
• Turnkey Solution – Includes generator, amplifier, coupler, and switching solutions

• DUT Current Ratings: 40A, 76A, 114A, 152A, 190A, 228A
• Voltage Ripple: Up to 200 kHz (500 kHz)
• Amplifier: BOLAB 100-TS Series 4-quadrant system
• Load Dump Generator: BOLAB 10/63-210 1C
• Switching: FIS 100-xx & FIS SM 96-2 (expandable)
• Power Supply: BOLAB or third-party compatible
• High-Voltage & Insulation Testing: G1-1G-T & 90-4K
• Modular & Scalable: Full ISO 16750-2:2023 compliance

• DC - 200 kHz bandwidth DC 
• MHz (small signal -3 dB)
• Output voltage ±75 Vpk
• Rise / fall time 100 V/µs
• USB interface standard, LAN optional
• Analog control input 0 ... ±10 V for control of voltage and current
• Monitor outputs for measured voltage and current values (not all models)
• Modularly extensible via master-slave mode
• Parallel and Series Connections for two or more units

• DC - 200 kHz bandwidth DC 
• MHz (small signal -3 dB)
• Output voltage ±75 Vpk
• Rise / fall time 100 V/µs
• USB interface standard, LAN optional
• Analog control input 0 ... ±10 V for control of voltage and current
• Monitor outputs for measured voltage and current values (not all models)
• Modularly extensible via master-slave mode
• Parallel and Series Connections for two or more units