Accessories for Generators

The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.

The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

The original EMC EPS 70x150cm Support is white Expanded Polystyrene (EPS)

• 150 x 100 x 70 cm.
• Sit on top of a standard 80cm test table for a 150cm height
• < 1.04 Permittivity
• A new design can be pre-built or shipped flat, self-assembled, glued onsite

The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The original EMC PLA blocks are 3D printed with PLA plastic. They are extremely durable and versatile for the EMC environment. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with this lightweight and EUT support. The surface is easily wiped clean for continued years of everyday use. Ideal for use in EMC testing for EUT and cable supports. The EMC PLA Blocks are crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 6 sides and allows for stacking and locking together. They are conveniently sold in kits in tote bins for secure storage. Each block has features for looping rubber bands, zip ties, or velcro straps. these features can be used to lock blocks together or to hold EUT/DUT wiring down to the blocks. 

The original ABSOLUTE EMC Monopole is explicitly designed for the EMC market. A low-cost and easy-to-use monopole with no metallic parts, with the exception of the antenna connection screw. The EMC Monopole is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. The monopole design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

The original EMC EPS Bar is white Expanded Polystyrene can optional be painted coating to extend durability. They come in dimensional metric sizes of 100 x 8.5 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Bar is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 4 sides allows for easy positioning and test setups.

The original EMC EPS 70cm Support is white Expanded Polystyrene. They come in dimensional metric sizes of 40 x 60 x 70 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. Since the EMC EPS 70cm Support is made from a denser EPS rating, it is crush resistance and able to withstand heavy weight loads without deforming. 

The original EMC EPS Cube is white Expanded Polystyrene can optional a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 10 cm which matches EUT height requirements for IEC testing above the ground plane for IEC 61000-4-5 and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Cube is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The original EMC EPS Pad is white Expanded Polystyrene, which can optionally be a painted coating to extend durability. They come in dimensional metric sizes of 5 x 50 x 50 cm, which matches EUT height requirements for IEC testing above the ground plane for ISO, MIL, IEC 61000-4-5, and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. It is ideal for use in EMC testing for EUT and cable supports. The EMC EPS Pad is crush-resistant and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The ABSOLUTE EMC TP-Ball Head is designed to mount a camera or other lightweight item with complete position control. Constructed of PLA plastic, only the 1/4"-20 screw is metal. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC TP-Cable Support is designed to hold wires, Coax, or waveguide parallel to the ground. This is useful in some cases for test setups where the antenna cable needs to be held back and away from the test area. Or in cases where EUT wires can not bend and need to be held up off the floor. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps to tie down cables or a 1m EPS bar. This rugged cable tray is a good match with the ABSOLUTE EMC Tripod or monopole.