ONYX 30, 30kV ESD Simulator
ESD Test Table Kit
AEMC-HVM100kV ElectroStatic HV Meter
SESD 8800-4: ESD Verification Set
SESD 272 Grounding cable for ESD
SESD 271 Vertical Coupling Plate (VCP) for ESD
SESD 302x Test tip's for ESD
SESD 30 T 1000 Support arm
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
SESD 230: ESD - Simulator 30 kV
SESD 216: ESD - Simulator 16,5 kV
Products
ONYX 16, 16kV ESD Simulator
Onyx 16
- +/- 16kV air and Contact Discharge
- 150pF/330Ohm Standard, Other networks available
- >16 hour Battery life, AC mains option
- Optional Software
ONYX 30, 30kV ESD Simulator
Onyx 30
- +/- 30kV air and Contact Discharge
- 150pF/330Ohm Standard, Other networks available
- >16 hour Battery life, AC mains option
- Optional Software
ESD Test Table Kit
The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.
AEMC-HVM100kV ElectroStatic HV Meter
- High input impedance ≥ 100 G Ohm
- Wide measurement ± 1V ~ 100 kV
- High accuracy and resolution ± 1% ± 2 counts
- Portable with large LCD/LED display 4 ½ Digit LCD
- Battery or AC supply
- Measure DC up to 100kV
SESD 8800-4: ESD Verification Set
ESD - Generators verified according to the standard International Electro technical Commission 61000-4-2, ISO 10605 and other. The measurements of the single pulses take place with a special 2 ohm shunt. For the correct verification of the ESD impulses an oscilloscope is necessary with a minimum bandwidth of - 2 GHz acc. IEC 61000-4-2, 2008 and - 1 GHz acc. ISO 10605, 2008. The ESD verification set SESD 8800-4 works up to 4 GHz and fulfilled the request of the double bandwidth regarding to the measurement bandwidth.
SESD 272 Grounding cable for ESD
2m Grounding cable for ESD immunity tests
SESD 271 Vertical Coupling Plate (VCP) for ESD
The Vertical Coupling Plate (VCP) is used in conjunction with ESD generators to simulate indirect discharges on metallic objects that are near a test object. The bleeder resistors contained in the ground wire of the VCP serve to prevent the applied charge from vanishing immediately after the discharge of the ESD generator to the VCP, thereby increasing the effect of the ESD test.
SESD 302x Test tip's for ESD
Avalible ESD Test Tips for replacment or different aplications.
SESD 30 T 1000 Support arm
Support arm with balancer for ESD test station
- Support arm with the carriage
- 360 degrees pivotable
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
The ESD-Sense has been developed with EMC test laboratories in mind to enable a “go / no-go” verification of the ESD generator output prior to test.
SESD 230: ESD - Simulator 30 kV
IEC / EN 61000-4-2 The test generator SESD 230 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods; Test voltage max. 30,0 kV AIR und CON; Discharge impedance 150pF/330 Ohm (IEC); Battery or mains operation; Predefined tests, standard and other
SESD 216: ESD - Simulator 16,5 kV
IEC / EN 61000-4-2 The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods; Air discharge (AIR) and Contact discharge (CON); Test voltage max. 16,5 kV AIR, max. 10,0 kV CON; Discharge impedance 150pF/330 Ohm (IEC); Battery or mains operation; Predefined tests - standard and other
