FIS 100-200 Fast Interrupt Switch 100V/200Amps
Product Description
The Fast Power Switch (FPS) is a device with several discrete switched power stages, including internal loads, which enable the user to perform voltage dips and brief interruptions on the device under test (DUT / load), mainly targeted at automotive vehicle manufacturers to comply with LV124 and LV148 test norms. The FPS is fitted with a flexible configuration of small signal switch cards for lower currents. These provide brief interruptions for signals such as CAN, Lin, Flexray etc.
The FPS can be incorporated into standard 19-inch rack systems for ease of testing and be remotely controlled and monitored via a simple Byte-Protocol over USB. It can switch between different power stage configurations to enable various DUT testing scenarios. All of the power stages are fault-protected against over-current. Additionally, the main power stage has built-in temperature, frequency, and passive surge protection to safeguard it during the most common operating circumstances.
Low noise, temperature-controlled fans allow for quiet operation.
Features
- High current power stage (uni-directional)
- Up to 32 channels for switching low-current signals (bi-directional)
- Switching of resistive, inductive, capacitive passive, and active loads/devices
- Input voltage up to 100V
- Output current up to 200A DC
- Source and sink DUT currents of up to 1500APK for 1ms
- Switchable DC link input capacitor
- Switchable charge resistor to ease operation with various DC supplies
- Two trigger input (A & B) single ended from 5V up to 20V
- One trigger output 0-5V to control additional testing-equipment
- One analog FPS output voltage monitor with f3dB=10Mhz Bandwidth
- USB port (emulated com port)
- Device supply: 230V 50Hz
Applications
- General lab applications for research, development, and testing
- Component tests
- Automotive equipment testing in compliance with LV128 & LV148
- Automated test systems
Parameters |
Specification |
Conditions/ Remarks |
Main power stage (1x) |
|
|
Input voltage |
|
Input current |
200A DC |
|
Output current |
200ADC+/-1500APeak for <1ms |
capacitive load, low repetition rate>1s |
trise / tfall |
<100ns |
measured at 100V input & resistive load |
Switch on-resistance |
<900µOhm |
S1 & S2 On resistancemeasured at DC at the device output |
Pout,max, DC |
10kW |
depends on load resistance, thermally limited |
Pout,max, Pulse |
5kW |
100kHz inductive load, 50% duty |
Current direction |
uni-directional |
Switch-blocking voltage direction |
Overcurrent-protection |
Yes |
All switches open after OCP event for >5s |
Overvoltage-protection |
Yes, passive against surge at input & output |
|
Input buffering |
9mF, low ESR electrolytic caps |
switchable |
Input load resistance |
45Ohm |
switchable |
Internal loads |
0.1Ohm & 10kOhm |
|
Internal 0.1Ohm maximum power & energy dissipation |
200W DC Frequency/pulse repetition > 1s |
Temperature-protection |
Yes |
S1, S2, 0.1Ohm |
Isolation |
Complete isolation from PE/chassis of the power stage |
|
|
Small Signal switches (x32) |
|
|
Input voltage |
<60V |
Both polarities |
Maximum current |
2A DC |
|
Overcurrent-protection |
Yes, analog & fuse protected with OCP blanking 5µs-500µs |
Blanking time beginning with trigger rising edge |
Overvoltage-protection |
Yes, passive surge protection |
|
Temperature-protection |
No |
|
Isolation |
Each channel is completely galvanically isolated from each other and from chassis |
|
Bandwidth |
50Mhz |
|
|
Trigger In (A & B) |
|
|
Trigger input |
5-20V single ended |
|
Trigger delay |
<900ns |
From trigger In to gate driver |
Trigger Out |
|
|
Trigger output |
0-5V single ended |
|
Trigger maximum frequency |
100kHz |
100kHz square wave, 50% duty |
Isolation |
All reference potential is interconnected to chassis GND / PE |
|
|
Monitoring |
|
|
Output |
+/-10V |
|
Attenuation |
1:25+/- 100V == +/- 2V |
|
Bandwidth |
<10Mhz |
Connected internally to the device outputslow capacitive loads with high rise & fall times may look distorted due to higher required bandwidth |
Remote |
USB |
|
Physical Characteristics |
|
|
AC Power |
230VAC 50-60Hz |
for internal 12V Supply, Pmax~25W |
Ambient operating temperature |
10°C to 40°C |
|
Humidity |
80% or less at 40°C |
|
Cooling |
Forced air |
Hot air expelled at rear panel |
Dimensions (WxHxD) |
133x482x518 |
|
Weight |
~6kg |
|
|