RF Test Accessories

The EPS Test Table Lt is a simple, inexpensive solution for your EMI testing. It is made from durable, expanded polystyrene (EPS) material and can be customized to your requirements. Complies with CISPR, ISO, & IEC requirements for having a low permittivity and can be used for additional standards.

• High strength EPS 3lb per ft3
• Low Permittivity >1.04
• Made for moderate 200 lb.
• Options
• vinyl topper with your company logo 
• epoxy coating for the top (can be combined with vinyl)

The EPS Test Table is a simple, inexpensive solution for your EMI testing. It is made from durable, expanded polystyrene (EPS) material and can be customized to your requirements. Complies with CISPR, ISO, & IEC requirements for having a low permittivity and can be used for additional standards.

• High strength EPS 3lb per ft³
• Low Permittivity >1.04
• Made for high loading 500 lb.
• Options
• vinyl topper with your company logo (shown in picture)
• epoxy coating for the top (can be combined with vinyl)

The Wood Test Table is a simple, inexpensive solution for your EMC testing. The table is built to be ship flattened to reduce shipping costs and easily assembled on site quickly. The picture is shown with a ground plane.

The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.

Absolute EMC offers an assortment of injection test kits for the use of conducted immunity. The kits can be used with many available conducted immunity systems, including the Schlöder CDG 7000, to make selection and setup easy. All calibration fixtures, injection clamps, attenuators, and termination resistors necessary for meeting the requirements of conducted immunity systems. All all-in-one systems are covered. 

The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

• 10 kHz - 3 GHz, 30dB Gain, 5dB N.F.
• Compensation long cable loss for EMI Measurement
• Improve system noise floor flatness
• High EMI performance
• High linearity LNA for EMI measurement
• High dynamic range
• Unconditionally Stable
• State-of-the-Art Technology

The original EMC EPS 5CM Sheets are white Expanded Polystyrene with 10cm x 10cm indentations for easy measurements. It can be cut down to size with the included razor knife. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for the use in EMC testing for EUT and cable supports. The EMC EPS 5CM SHEETS are crush resistance able to withstand heavy weight loads without deforming. 1cm marking on the top side allows for easy positioning and test setups. Conveniently sold as sheets other sizes possible just ask. 

The original EMC EPS 70x150cm Support is white Expanded Polystyrene (EPS)

• 150 x 100 x 70 cm.
• Sit on top of a standard 80cm test table for a 150cm height
• < 1.04 Permittivity
• A new design can be pre-built or shipped flat, self-assembled, glued onsite

The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The original EMC PLA blocks are 3D printed with PLA plastic. They are extremely durable and versatile for the EMC environment. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with this lightweight and EUT support. The surface is easily wiped clean for continued years of everyday use. Ideal for use in EMC testing for EUT and cable supports. The EMC PLA Blocks are crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 6 sides and allows for stacking and locking together. They are conveniently sold in kits in tote bins for secure storage. Each block has features for looping rubber bands, zip ties, or velcro straps. these features can be used to lock blocks together or to hold EUT/DUT wiring down to the blocks. 

The original ABSOLUTE EMC Tripod is explicitly designed for the EMC market. A low-cost and easy-to-use tripod with no metallic parts with the exception of the antenna connection screw. The EMC Tripod is easy to assemble, take apart, and store. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. If any plastic pieces break, they will be replaced free of charge for the product's life.