Antenna Mast/Positioner

The EPS Test Table Lt is a simple, inexpensive solution for your EMI testing. It is made from durable, expanded polystyrene (EPS) material and can be customized to your requirements. Complies with CISPR, ISO, & IEC requirements for having a low permittivity and can be used for additional standards.

• High strength EPS 3lb per ft3
• Low Permittivity >1.04
• Made for moderate 200 lb.
• Options
• vinyl topper with your company logo 
• epoxy coating for the top (can be combined with vinyl)

The EPS Test Table is a simple, inexpensive solution for your EMI testing. It is made from durable, expanded polystyrene (EPS) material and can be customized to your requirements. Complies with CISPR, ISO, & IEC requirements for having a low permittivity and can be used for additional standards.

• High strength EPS 3lb per ft³
• Low Permittivity >1.04
• Made for high loading 500 lb.
• Options
• vinyl topper with your company logo (shown in picture)
• epoxy coating for the top (can be combined with vinyl)

The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

The original EMC EPS 5CM Sheets are white Expanded Polystyrene with 10cm x 10cm indentations for easy measurements. It can be cut down to size with the included razor knife. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for the use in EMC testing for EUT and cable supports. The EMC EPS 5CM SHEETS are crush resistance able to withstand heavy weight loads without deforming. 1cm marking on the top side allows for easy positioning and test setups. Conveniently sold as sheets other sizes possible just ask. 

The double telescopic antenna mast/tripod is continuously height-adjustable. The mast rods are made of glass fiber to avoid unwanted reflexions. The modular design makes it possible to use different telescope parts and it can be mounted on a mast foot made of stainless steel or one made out of low-reflective fiberglass. Both of them provide a secure stand and easy adjustment on uneven ground. Antennas or adapters can be mounted on the 3/8" male thread.

The original ABSOLUTE EMC Tripod is explicitly designed for the EMC market. A low-cost and easy-to-use tripod with no metallic parts with the exception of the antenna connection screw. The EMC Tripod is easy to assemble, take apart, and store. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. If any plastic pieces break, they will be replaced free of charge for the product's life.

The original ABSOLUTE EMC Monopole is explicitly designed for the EMC market. A low-cost and easy-to-use monopole with no metallic parts, with the exception of the antenna connection screw. The EMC Monopole is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. The monopole design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

The ABSOLUTE EMC TP-Ball Head is designed to mount a camera or other lightweight item with complete position control. Constructed of PLA plastic, only the 1/4"-20 screw is metal. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC TP-Cable Support is designed to hold wires, Coax, or waveguide parallel to the ground. This is useful in some cases for test setups where the antenna cable needs to be held back and away from the test area. Or in cases where EUT wires can not bend and need to be held up off the floor. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps to tie down cables or a 1m EPS bar. This rugged cable tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC TP-Item Tray is designed for holding items up. There is often a need to elevate an item at a specific height. Or, in cases where an antenna or transducer does not have ideal mounting, the tray can hold the item with velcro straps or zip ties. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps. This rugged Item tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC MP-Rotator is attached to a 1" Wood Dowel or tube. It holds a second Dowel/tube that can be rotated 360deg to reach out over an obstacle such as a table. This gives the ability to position a camera or other measurement device over top of a test table or in positions where the base/feet of the EMC Monopole/tripod prohibit easy positioning. Constructed of PLA plastic and includes a 36" Hard Wood Dowel. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC can design and produce Custom Antenna Adaptors. each adaptor is mad for your antennas and tripods or to be used on our Absolute EMC Tripod/monopod stands. Adaptors can be designed to rotate the antenna in the center from horizontal to vertical and position it at the center of gravity of the antenna so it sits easily on the antenna stand. Cost is set based on the size and complexity of the adaptor.