Support arm with balancer for ESD test station

• The only support arm is made from non-metal 
• 1.5" Fiberglass Tubes,
• 3D Printed: Cage, holder, base
• Custom ESD simulator adaption
• Balancer is plastic housing and string (only the spring is metallic)
• Only the system meets the metal-free area requirements of standards
• Support arm with the carriage
• 360 degrees pivotable
• Customized attachment to the table included

The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.

The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

The original EMC EPS 70x150cm Support is white Expanded Polystyrene (EPS)

• 150 x 100 x 70 cm.
• Sit on top of a standard 80cm test table for a 150cm height
• < 1.04 Permittivity
• A new design can be pre-built or shipped flat, self-assembled, glued onsite

The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The original EMC PLA blocks are 3D printed with PLA plastic. They are extremely durable and versatile for the EMC environment. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with this lightweight and EUT support. The surface is easily wiped clean for continued years of everyday use. Ideal for use in EMC testing for EUT and cable supports. The EMC PLA Blocks are crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 6 sides and allows for stacking and locking together. They are conveniently sold in kits in tote bins for secure storage. Each block has features for looping rubber bands, zip ties, or velcro straps. these features can be used to lock blocks together or to hold EUT/DUT wiring down to the blocks. 

The original ABSOLUTE EMC Monopole is specifically designed for the EMC market as a low-cost, easy-to-use solution with no metallic parts except for the antenna connection screw. It's easy to assemble and fully adjustable in height using the center mast section. Made from low permittivity materials, it's ideal for various EMC applications like holding antennas, cameras, RF field probes, and keeping cables off the floor. The monopole's compact design allows for easy maneuverability and reduces tripping hazards compared to tripods. Plus, any plastic pieces that break will be replaced free of charge for the life of the product.

The original EMC EPS Bar is white Expanded Polystyrene can optional be painted coating to extend durability. They come in dimensional metric sizes of 100 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Bar is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on 4 sides allows for easy positioning and test setups.

The original EMC EPS 70cm Support is white Expanded Polystyrene. They come in dimensional metric sizes of 40 x 60 x 70 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. Since the EMC EPS 70cm Support is made from a denser EPS rating, it is crush resistance and able to withstand heavy weight loads without deforming. 

The original EMC EPS Cube is white Expanded Polystyrene can optional a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 10 cm which matches EUT height requirements for IEC testing above the ground plane for IEC 61000-4-5 and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Cube is crush resistance and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

The original EMC EPS Pad is white Expanded Polystyrene, which can optionally be a painted coating to extend durability. They come in dimensional metric sizes of 5 x 50 x 50 cm, which matches EUT height requirements for IEC testing above the ground plane for ISO, MIL, IEC 61000-4-5, and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. It is ideal for use in EMC testing for EUT and cable supports. The EMC EPS Pad is crush-resistant and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

ESD - Generators verified according to the standard International Electro technical Commission 61000-4-2, ISO 10605 and other. The measurements of the single pulses take place with a special 2 ohm shunt. For the correct verification of the ESD impulses an oscilloscope is necessary with a minimum bandwidth of - 2 GHz acc. IEC 61000-4-2, 2008 and - 1 GHz acc. ISO 10605, 2008. The ESD verification set SESD 8800-4 works up to 4 GHz and fulfilled the request of the double bandwidth regarding to the measurement bandwidth.