400 - 6361, 2-Ch, 2.8MS/s, AnyWave Control Unit
400 - 6112, 2-Ch, 250kS/s, AnyWave Control Unit
ONYX 16, 16kV ESD Simulator
ONYX 30, 30kV ESD Simulator
Axos 8 - Compact 7kV Surge, Telecom, Ring Wave, 5kV EFT, Dips/Drops
Axos 5 - Compact 5kV EFT, Surge, Dips/Drops
100-TS, 4-Quadrant Current Amplifiers 400 W - 54,000 W
100-TS, 4-Quadrant Voltage Amplifiers 400 W - 54,000 W
FIS 100-200 Fast Interrupt Switch 100V/200Amps
Dips-Interrupts-Variations Test System 30kVA (43A) & 50kVA (75A) + 1 & 3-Phase
BLS SU 600, Matrix Switching Unit
Products
BOLAB ISO 21498 HV Test System & Ripple Generator
- Advanced Ripple Testing: Meets ISO 21498, LV123, VW 80300, Nissan MES PW 67602, Mazda, and emerging standards.
- Series Amplifier Integration: High accuracy ripple injection, minimal distortion, and enhanced safety.
- Waveform Versatility: Sine, square, trapezoidal, pulses, and triangle waveform generation.
- WaveMaster Software: Fast DUT impedance measurement, automated test sequences, and dynamic voltage/current control.
- High Power Capability: Ripple Voltage up to 100 Vpp, currents from 100A to 2000A+, and frequency range 10 Hz–300+ kHz.
- Future-Proof Design: Modular architecture for easy upgrades and adaptation to new standards.
400 - 6361, 2-Ch, 2.8MS/s, AnyWave Control Unit
WaveMaster + AnyWave
BOLAB WaveMaster software and the BOLAB AnyWave control unit allow the control of power supplies as well as 4 quadrant amplifiers via the analog interfaces.
The powerful and easy-to-use BOLAB WaveMaster software is unique in the world. Without any knowledge in software development, designing ordinary and complex waveforms is very easy. A graphic waveform editor allows the generation
of individual curves in no time. Also, with tabular input, all types of waveforms can be produced instantly.
400 - 6112, 2-Ch, 250kS/s, AnyWave Control Unit
WaveMaster + AnyWave
BOLAB WaveMaster software and the BOLAB AnyWave control unit allow the control of power supplies as well as 4 quadrant amplifiers via the analog interfaces.
The powerful and easy-to-use BOLAB WaveMaster software is unique in the world. Without any knowledge in software development, designing ordinary and complex waveforms is very easy. A graphic waveform editor allows the generation
of individual curves in no time. Also, with tabular input, all types of waveforms can be produced instantly.
ONYX 16, 16kV ESD Simulator
Onyx 16
- +/- 16kV air and Contact Discharge
- 150pF/330Ohm Standard, Other networks available
- >16 hour Battery life, AC mains option
- Optional Software
ONYX 30, 30kV ESD Simulator
Onyx 30
- +/- 30kV air and Contact Discharge
- 150pF/330Ohm Standard, Other networks available
- >16 hour Battery life, AC mains option
- Optional Software
Axos 8 - Compact 7kV Surge, Telecom, Ring Wave, 5kV EFT, Dips/Drops
Axos 8 - Compact
- Multi Tester with 16AMP CDN
- EFT/Burst 5kV IEC 61000-4-4
- Surge, Combination Wave 7kV IEC 61000-4-5
- Surge Magnetic field IEC 61000-4-9 (MSURGE-A loop antenna required)
- Ring Wave, 7kV IEC 61000-4-12 & ANSI
- Telicomm Wave, 7kV IEC 61000-4-5 & ITU
- AC Dips/Drops IEC 61000-4-11 (DIP 116 dips transformer required)
- DC Dips/Drops IEC 61000-4-29 (2x DC supplies required)
Axos 5 - Compact 5kV EFT, Surge, Dips/Drops
Axos 5 - Compact
- Multi Tester with 16AMP CDN
- EFT/Burst 5kV IEC 61000-4-4
- Surge, Combination Wave 5kV IEC 61000-4-5
- Surge Magnetic field IEC 61000-4-9 (MSURGE-A loop antenna required)
- AC Dips/Drops IEC 61000-4-11 (DIP 116 dips transformer required)
- DC Dips/Drops IEC 61000-4-29 (2x DC supplies required)
100-TS, 4-Quadrant Current Amplifiers 400 W - 54,000 W
- DC - 200 kHz bandwidth DC
- MHz (small signal -3 dB)
- Output voltage ±75 Vpk
- Rise / fall time 100 V/µs
- USB interface standard, LAN optional
- Analog control input 0 ... ±10 V for control of voltage and current
- Monitor outputs for measured voltage and current values (not all models)
- Modularly extensible via master-slave mode
- Parallel and Series Connections for two or more units
100-TS, 4-Quadrant Voltage Amplifiers 400 W - 54,000 W
- DC - 200 kHz bandwidth DC
- MHz (small signal -3 dB)
- Output voltage ±75 Vpk
- Rise / fall time 100 V/µs
- USB interface standard, LAN optional
- Analog control input 0 ... ±10 V for control of voltage and current
- Monitor outputs for measured voltage and current values (not all models)
- Modularly extensible via master-slave mode
- Parallel and Series Connections for two or more units
FIS 100-200 Fast Interrupt Switch 100V/200Amps
- High current power stage (uni-directional)
- Up to 32 channels for switching low-current signals (bi-directional)
- Switching of resistive, inductive, capacitive passive, and active loads/devices
- Input voltage up to 100V
- Output current up to 200A DC
Dips-Interrupts-Variations Test System 30kVA (43A) & 50kVA (75A) + 1 & 3-Phase
- Turnkey EMC test solution — ready to use with full hardware and software integration
- Fast voltage transitions (<5 µs) for full compliance with critical standards
- Covers all major IEC/EN 61000-4-X tests including -11, -13, -14, -27, -28, -34
- User-friendly ACSControl software with built-in test libraries and reporting
- Modular, scalable power platform from 30 kVA up to 2000+ kVA
- Versatile use beyond EMC: ideal for grid simulation, anti-islanding, and inverter testing
- Compact 19" rack-mounted units — easy system integration and footprint optimization
- Certified for global compliance (CE, UKCA, RoHS, EN/IEC EMC and safety standards)
BLS SU 600, Matrix Switching Unit
- Protocol reports
- Generation of waveforms with synchronous data acquisition
- Modular Expandable
- Individual Waveform Generation
- Standard Libraries included
- Unlimited Waveform size
- 2 different Waveforms synchronously
- DLL's for LabView, Vector CANoe / CAPL, C#, C++, ANSI C, Python, etc.
- Simulation of imported oscilloscope waveform
