RF Test Accessories

The ABSOLUTE EMC TP-Ball Head is designed to mount a camera or other lightweight item with complete position control. Constructed of PLA plastic, only the 1/4"-20 screw is metal. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC TP-Cable Support is designed to hold wires, Coax, or waveguide parallel to the ground. This is useful in some cases for test setups where the antenna cable needs to be held back and away from the test area. Or in cases where EUT wires can not bend and need to be held up off the floor. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps to tie down cables or a 1m EPS bar. This rugged cable tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC TP-Item Tray is designed for holding items up. There is often a need to elevate an item at a specific height. Or, in cases where an antenna or transducer does not have ideal mounting, the tray can hold the item with velcro straps or zip ties. Constructed of PLA plastic, slots for feeding velcro straps or zip-ties, and includes velcro straps. This rugged Item tray is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC MP-Rotator is attached to a 1" Wood Dowel or tube. It holds a second Dowel/tube that can be rotated 360deg to reach out over an obstacle such as a table. This gives the ability to position a camera or other measurement device over top of a test table or in positions where the base/feet of the EMC Monopole/tripod prohibit easy positioning. Constructed of PLA plastic and includes a 36" Hard Wood Dowel. This rugged adaptor is a good match with the ABSOLUTE EMC Tripod or monopole. 

The ABSOLUTE EMC can design and produce Custom Antenna Adaptors. each adaptor is mad for your antennas and tripods or to be used on our Absolute EMC Tripod/monopod stands. Adaptors can be designed to rotate the antenna in the center from horizontal to vertical and position it at the center of gravity of the antenna so it sits easily on the antenna stand. Cost is set based on the size and complexity of the adaptor. 

The TBFL1 is a combined transient limiter/attenuator/ high pass filter, designed to provide optimum protection of spectrum analyzer or measurement receiver inputs when carrying out conducted noise measurements or other measurements where the input levels cannot be predicted with certainty or where accidental overloads may occur.

The H20, H10, H5, and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies. The probes act similar to wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations which emit electromagnetic radiation. By changing to a probe with a smaller size, the origination of the emissions can be further narrowed down. With TBWA2 WIDEBAND AMPLIFIER/40DB

The H20, H10, H5, and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies. The probes act similar to wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations which emit electromagnetic radiation. By changing to a probe with a smaller size, the origination of the emissions can be further narrowed down. With TBWA2 WIDEBAND AMPLIFIER/20DB

The TBAS3 RF 10W attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box.

The TBCAS1 coaxial adapter set contains 44 pieces of the most common 50 Ohm coaxial adapters in a beechwood box

The TBAS1 RF 2W attenuator set

The TBAS2 RF SMA attenuator/termination set consists of a 3dB, 6dB, 10dB, 15dB, 20dB and 30dB SMA attenuators in a beechwood box. Furthermore, it contains two pieces SMA 50 Ohm terminations.