Warning light
EFTC-CK Calibration kit for burst coupling clamps
BCK 400 F Calibration kit for EFT/burst Generators
IMP 8, Impedance matching network for IEC 61000-4-5
SCK 105, Surge Calibration Kit
SCK 105 inBox, Surge Calibration Kit
VPS 250, Automatic Variack 0-250V 16Amps
Foot-switch Trigger
EFT 2012 EFT/Burst Capacitive Coupling Clamp
CAR CDN 2012 EFT/Burst Capacitive Coupling Clamp ISO
CCK20 Calibration kit for: PG 10-200, PG 12-360 and PG 20-100
Products
Emergency stop
Emergency stop switch for interrupting / close the internal safety circuits.
Warning light
Warning / signal lamps for visualizing the generator state. Signal red: "Warning Hazard", signal green: "all clear".
EFTC-CK Calibration kit for burst coupling clamps
The EFTC-CK is a calibration kit for burst/EFT coupling clamps as specified in IEC 6100-4-4:2012. It has been designed for calibration of coupling clamps like EFTC2012. The set consists of a transducer plate and a termination bracket (connecting adapter).
BCK 400 F Calibration kit for EFT/burst Generators
The Burst Calibration Kit has been designed to measure the pulse output voltage and the pulse output current of burst generators, e.g. the EFTG-CE5 or the burst generator sub-unit of the Multi-CE5. It essentially consists of a load resistor, a pulse voltage divider, and a double-shielded coaxial cable. ? Burst Calibration Kit ? Input voltage: 5 kV ? Ratio, 200/400:1 ? Bandwidth: 400 MHz
IMP 8, Impedance matching network for IEC 61000-4-5
The external impedance IMP8 is the impedance, required for the pulse specifications according to standard IEC 61000-4-5 Ed.3, for measuring the pulse output voltage of surge generators.
SCK 105, Surge Calibration Kit
The Surge Calibration Kit has been designed to measure the pulse output voltage and the pulse output current of surge generators, e.g. a combination wave generator. It essentially consists of a pulse voltage divider, a pulse current measuring resistor, and a double-shielded coaxial cable.
SCK 105 inBox, Surge Calibration Kit
The Surge Calibration Kit has been designed to measure the pulse output voltage and the pulse output current of surge generators, e.g. a combination wave generator. It essentially consists of a pulse voltage divider, a pulse current measuring resistor, and a double-shielded coaxial cable. The unit is easy to connect and use for everyday pulse verification.
VPS 250, Automatic Variack 0-250V 16Amps
Motor-driven variable transformer, controlled by Multi-CE5 or Multi-CE7, used for power supply variation acc. to IEC 61000-4-11 and setting current for IEC 61000-4-8 Magnetic fields
Foot-switch Trigger
Footswitch to trigger certain generator functions.
EFT 2012 EFT/Burst Capacitive Coupling Clamp
The Capacitive Coupling Clamp, EFTC 2012, provides the ability to couple Burst / EFT pulses to data lines. It can also be used for coupling to main lines where no CDN is available, for example, high current lines >200 A.
CAR CDN 2012 EFT/Burst Capacitive Coupling Clamp ISO
The coupling clamp CDN 2012 conforms exactly to the requirements of ISO 7637-3 and other standards, guaranteeing that tests are carried out in strict compliance with the standard. The CDN allows the fast nanosecond pulse bursts ( ISO 3a and 3b) to be injected in cable runs. Very high impedance signal lines are also to be found in vehicles on which the disruptive effects of ISO pulses 1 and 2 can also show up through capacitive coupling.
CCK20 Calibration kit for: PG 10-200, PG 12-360 and PG 20-100
The Capacitor Calibration Kit CCK has been designed to measure the pulse output voltage of surge generators PG10-200, PG12-360 and PG20-100.
