RF Test Accessories

The original EMC EPS 70cm Support is white Expanded Polystyrene. They come in dimensional metric sizes of 40 x 60 x 70 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. Since the EMC EPS 70cm Support is made from a denser EPS rating, it is crush resistance and able to withstand heavy weight loads without deforming. 

The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

• 10 kHz - 3 GHz, 30dB Gain, 5dB N.F.
• Compensation long cable loss for EMI Measurement
• Improve system noise floor flatness
• High EMI performance
• High linearity LNA for EMI measurement
• High dynamic range
• Unconditionally Stable
• State-of-the-Art Technology

The original EMC EPS 70x150cm Support is white Expanded Polystyrene (EPS)

• 150 x 100 x 70 cm.
• Sit on top of a standard 80cm test table for a 150cm height
• < 1.04 Permittivity
• A new design can be pre-built or shipped flat, self-assembled, glued onsite

• 10 kHz - 3 GHz, 40dB Gain, 5dB N.F.
• Compensation long cable loss for EMI Measurement
• Improve system noise floor flatness
• High EMI performance
• High linearity LNA for EMI measurement
• High dynamic range
• Unconditionally Stable
• State-of-the-Art Technology

The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.

• Non-Metallic Design: All parts are non-metallic except the antenna connection screw, ensuring minimal interference in EMC testing.
• 3D-Printed PLA & Hardwood Construction: Includes 1" hardwood dowels that are adjustable up to 3 feet; fiberglass dowels are also available.
• Height Adjustability: Ranges from 37" to 68" using a 1-inch center mast.
• Stability: Comes with leveling feet and an optional weight ballast to ensure stability.

The original EMC EPS Pad is white Expanded Polystyrene, which can optionally be a painted coating to extend durability. They come in dimensional metric sizes of 5 x 50 x 50 cm, which matches EUT height requirements for IEC testing above the ground plane for ISO, MIL, IEC 61000-4-5, and IEC 61000-4-6. Keep your test setup looking professional with these lightweight and soft EUT supports. It is ideal for use in EMC testing for EUT and cable supports. The EMC EPS Pad is crush-resistant and able to withstand heavy weight loads without deforming. 1cm marking on all 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.

• 20 MHz - 3 GHz, 30dB Gain, 5dB N.F.
• Compensation long cable loss for EMI Measurement
• Improve system noise floor flatness
• High EMI performance
• High linearity LNA for EMI measurement
• High dynamic range
• Unconditionally Stable
• State-of-the-Art Technology

The ABSOLUTE EMC Bar Clamp is specifically designed for the EMC market, providing a low-cost, easy-to-use solution with no metallic parts. It is highly adjustable, reliable, and ideal for various EMC testing applications. The EMC Bar Clamp is made from low permittivity materials, making it suitable for holding tables together or securing the DUT/EUT in position during testing.

The original EMC EPS 5CM Sheets are white Expanded Polystyrene with 10cm x 10cm indentations for easy measurements. It can be cut down to size with the included razor knife. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for the use in EMC testing for EUT and cable supports. The EMC EPS 5CM SHEETS are crush resistance able to withstand heavy weight loads without deforming. 1cm marking on the top side allows for easy positioning and test setups. Conveniently sold as sheets other sizes possible just ask. 

RefRad X Comb Generator The newly developed battery-operated comb generator RefRad X is specially designed for checking the quality of radiated and conducted EMC and EMF tests. Initially introduced at the beginning of 2008, several modifications in the print design have enhanced the RefRad X considerably.