LSProbe 1.2 Variant F, Laser Powered Field Probe, 10 Hz to 8.2 GHz, <3 V/m … >1,000 V/m
LSProbe 1.2 Variant G, Laser Powered Field Probe, 10 kHz to 8.2 GHz, <15 V/m … >15,000 V/m
Absolute EMC106 18GHz Low-Loss Coax
ESD Test Table Kit
Injection Clamp Kits (ICK) EM and BCI Clamps
LSFrame System for multiple probe usage with minimal rack space
ABSOLUTE EMC Monopole Probe Stand
EMC001330SE, 10 kHz - 3 GHz, 30dB gain, Portable Low Noise Preamplifier
FS-SET 7100, 9 kHz - 1 GHz, Active Nearfield Probe Set
EMC EPS 5cm Sheets - low permittivity EUT Support for high frequency testing
EMC EPS Block - 10 x 10 x 5 cm, EUT support
Products
DGA 9553 BNC, Attenuator, 1 watts, 2GHz, 3, 6, 10, 20, and 30 dB
DGA 9553 BNC is a bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions.
There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration, an attenuator directly at the pulse generator output is inevitable.
- 3, 6, 10, 20, and 30 dB Values available
- 50 Ohm, Low VSWR
- 1 Watts
LSProbe 1.2 Variant F, Laser Powered Field Probe, 10 Hz to 8.2 GHz, <3 V/m … >1,000 V/m
The LSProbe 1.2 Variant F Field Probe is a high-speed, high-accuracy, and high-dynamic range electric-Field probe.
- Its standard frequency range of 10 Hz – 8.2 GHz. 1,000 V/m
- Best-in-class compensation of linearity, frequency, and temperature guarantees accurate measurements from less than 0.1 to at least 1,000 V/m.
- A dynamic range of 100 dB is achieved for many frequencies, enabling Field measurements at more than 10,000 V/m.
- Customized high Field-strength „X“-variants, supporting up to 30,000 V/m and a damage level of 100,000 V/m, are available upon request.
LSProbe 1.2 Variant G, Laser Powered Field Probe, 10 kHz to 8.2 GHz, <15 V/m … >15,000 V/m
The LSProbe 1.2 Variant E Field Probe is a high-speed, high-accuracy, and high-dynamic range electric-Field probe.
- Its standard frequency range of 10 kHz – 8.2 GHz. 15,000 V/m
- Best-in-class compensation of linearity, frequency, and temperature guarantees accurate measurements from less than 15 to at least 15,000 V/m.
- A dynamic range of 100 dB is achieved for many frequencies, enabling Field measurements at more than 10,000 V/m.
- Customized high Field-strength „X“-variants, supporting up to 30,000 V/m and a damage level of 100,000 V/m, are available upon request.
Absolute EMC106 18GHz Low-Loss Coax
The Absolute EMC106 series of cables is a very high-performing Coax operating up to 18GHz with incredibly low losses. It can be used for high-power applications resulting in more power reaching your antenna. Also ideal for emissions testing up to 18GHz. allowing for long-distance runs with less loss.
ESD Test Table Kit
The ESD Test Table Kit is a simple inexpensive solution for your ESD testing. Complies to the requirements of IEC 61000-4-2 and can be used for additional standards. Comes with a Horizontal Coupling Plane (HCP), resistive cable to tie HCP to floor ground plane, bleeder wire for discharging ungrounded battery powered EUTs, 0.05mm insulator and an alternative low impedance ground for using the table for additional setups such as IEC 61000-4-6 requirements.
Injection Clamp Kits (ICK) EM and BCI Clamps
Absolute EMC offers an assortment of injection test kits for the use of conducted immunity. The kits can be used with many available conducted immunity systems, including the Schlöder CDG 7000, to make selection and setup easy. All calibration fixtures, injection clamps, attenuators, and termination resistors necessary for meeting the requirements of conducted immunity systems. All all-in-one systems are covered.
LSFrame System for multiple probe usage with minimal rack space
LSFrame is LUMILOOP’s solution for straight-forward and reliable integration of one or more LUMILOOP products in a LAN-controlled, standard 19 inch form factor appliance.
LSFrame can host:
- LSProbe Laser-Powered Electric-Field Probes,
- CI 250+
- LSPM High-Speed Power Meters, and
- LSPM+ High-Speed Power Meters, and
- upcoming LUMILOOP products.
ABSOLUTE EMC Monopole Probe Stand
The original ABSOLUTE EMC MP-Probe Stand is explicitly designed for the EMC market. A low-cost and easy-to-use probe stand with no metallic parts. The EMC Monopole Probe Stand is easy to assemble. It is fully adjustable in height with the center mast section. Materials used are low permittivity allowing for use in most EMC applications to hold antennas, cameras, RF field probes, cables off the floor, and other support possibilities. No metal is used in any part of the stand. The field probe holders use PTEG plastic screws to hold the probe in place. The MP Probe Stand design allows for a small footprint for easy maneuvering around and reduces tripping caused by tripods. If any plastic pieces break, they will be replaced free of charge for the product's life.
EMC001330SE, 10 kHz - 3 GHz, 30dB gain, Portable Low Noise Preamplifier
- 10 kHz - 3 GHz, 30dB Gain, 5dB N.F.
- Compensation long cable loss for EMI Measurement
- Improve system noise floor flatness
- High EMI performance
- High linearity LNA for EMI measurement
- High dynamic range
- Unconditionally Stable
- State-of-the-Art Technology
FS-SET 7100, 9 kHz - 1 GHz, Active Nearfield Probe Set
Nearfield Probe Set including:
- HFSL 7101 Active Near Field Probe (magnetic), 9 kHz - 30 MHz
- HFSH 7102 Active Near Field Probe (magnetic), 4 MHz - 1000 MHz
- EFS 7103 Active Near Field Probe (electric), 9 kHz - 1000 MHz
- and Separator EW 7110 and AC/DC adaptor ACDC 7110 in storing case
EMC EPS 5cm Sheets - low permittivity EUT Support for high frequency testing
The original EMC EPS 5CM Sheets are white Expanded Polystyrene with 1cm x 1cm indentations for easy measurements. It can be cut down to size with the included razor knife. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for the use in EMC testing for EUT and cable supports. The EMC EPS 5CM SHEETS are crush resistance able to withstand heavy weight loads without deforming. 1cm marking on the top side allows for easy positioning and test setups. Conveniently sold as sheets other sizes possible just ask.
EMC EPS Block - 10 x 10 x 5 cm, EUT support
The original EMC EPS Block is white Expanded Polystyrene can optional be covered in a vinyl covering on top and sides or with a painted coating to extend durability. They come in dimensional metric sizes of 10 x 10 x 5 cm. Keep your test setup looking professional with these lightweight and soft EUT supports. Ideal for use in EMC testing for EUT and cable supports. The EMC EPS Block is crush resistance able to withstand heavy weight loads without deforming. 1cm marking on 6 sides allows for easy positioning and test setups. They are conveniently sold in kits in tote bins for secure storage.
