CS-50, 2 way splitter, 50 Ohms acc. EN 50561-1
SPLIT 100, 2 way splitter, 100 Ohms acc. EN 50561-1
SYMAT 40, Symmetrical Step Attenuator, 100 Ohms acc. EN 50561-1
SY 9223-50561-1, Symmetrical Transformer, 50 to 100 Ohms acc. EN 50561-1
CU 50561-1, Coupling Unit , acc. EN 50561-1
AC Separator, acc. EN 50561-1
SW 9602, 10 kHz - 200 MHz Current Transformer
SW 9603, 9 kHz - 150 MHz Current Transformer
SW 9605, 9 kHz - 80 MHz Current Clamp
SW 9606, 9 kHz - 200 MHz Current Clamp
CA 9608, DC - 500 MHz Universal Calibration Jig for Current Clamps
Products
NNBL 8240, 9 kHz - 100 MHz, 800A, 50µH Single Path LISN
- Measurement of interference for MIL-STD-461/462
- 9 kHz - 100 MHz
- 1000VDC / 650VAC 50/60Hz
- Max current 800A, (1000A limited time)
- Impedance of each path: 50 µH +5 Ω || 50 Ω ±20 %
CS-50, 2 way splitter, 50 Ohms acc. EN 50561-1
- A resistive, unsymmetrical two-way splitter
- The impedance of 50 Ω
- Acc. to EN 50561-1:2012 which is explained in chapter 9.2.
- Figure 4 shows the measurement setup with the available components
SPLIT 100, 2 way splitter, 100 Ohms acc. EN 50561-1
- A resistive, unsymmetrical two-way splitter
- The impedance of 100 Ω
- Acc. to EN 50561-1:2012 which is explained in chapter 9.2.
- Figure 4 shows the measurement setup with the available components
SYMAT 40, Symmetrical Step Attenuator, 100 Ohms acc. EN 50561-1
- Symmetrical 100 Ω step attenuator
- Switchable between 0 dB, 10 dB, 20 dB, 30 dB, 40 dB and 50 dB
- For measurement of PLC or PLT to discover dynamic performance
- Acc. EN 50561-1:2012 chapter 9.2. Figure 4 shows the setup
SY 9223-50561-1, Symmetrical Transformer, 50 to 100 Ohms acc. EN 50561-1
- Symmetrical transformer
- Transforms an unsymmetrical 50 Ω signal into a symmetrical signal with an impedance of 100 Ω
- Attenuates the power by 8 dB
- Acc. to EN 50561-1:2012, chapter 9.2. Figure 4 shows the setup, figure 5 shows the principle diagram
CU 50561-1, Coupling Unit , acc. EN 50561-1
- The coupling unit for measurements at powerline transmission devices.
- Acc. standard EN-50561-1
- Combined with two-line impedance stabilization networks (LISN)
AC Separator, acc. EN 50561-1
- The AC separators provide connectivity between the LISNs and the device under test (DuT) respectively the auxiliary equipment (AE) as well as the connection to the measurement setup.
- Two of the R/C elements required by the standard EN 50561-1
- Built-in (1 M || 100 nF).
- Two identical AC separators are required
SW 9602, 10 kHz - 200 MHz Current Transformer
- Current Transformer
- Shielded
- 0.01 - 200 MHz
- Transfer Impedance: 1 Ohm for wires up to 6.5 mm
SW 9603, 9 kHz - 150 MHz Current Transformer
- Current Transformer
- Shielded
- 0.09 - 150 MHz
- Transfer Impedance: 1 Ohm for wires up to 14 mm
SW 9605, 9 kHz - 80 MHz Current Clamp
- Clamp-on Current Clamp
- 0.09 - 80 MHz
- Transfer Impedance: 1 Ohm for wires up to 23 mm
SW 9606, 9 kHz - 200 MHz Current Clamp
- Clamp-on Current Clamp
- 0.09 - 200 MHz
- Transfer Impedance: 8 Ohm for wires up to 23 mm
CA 9608, DC - 500 MHz Universal Calibration Jig for Current Clamps
- Clamp-on Current Clamp
- 0.09 - 200 MHz
- Transfer Impedance: 8 Ohm for wires up to 23 mm
