VDips-Sense Quick pre-check of IEC 61000-4-11 Dips
CAB1001 Inrush Compensator IEC 61000-4-11 Dips
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
PG 6-401, Capacitor Tester, 6kV
IPG 250, Pulse generator 250V
Automotive Transients to FORD and JLR
Automotive FORD JLR CI250 Timing Jig
ESD-Soft 6: Control software for ESD
HILO Remote, For HILO/TEST Gernerators
CAR Cal Kit, Standard loads for Automotive Testing
CCK, Capacitor Calibration Kit for: PG10-200, PG12-360 and PG20-100
Products
Trans-Sense Quick pre-check of IEC 61000-4-4 EFT
The Trans Sense has been developed with EMC test laboratories in mind to enable a “go/no-go” verification of the transient generator output prior to the test.
VDips-Sense Quick pre-check of IEC 61000-4-11 Dips
The VDips-Sense has been developed with EMC test laboratories in mind to enable a “go / no-go” verification of the Voltage Dip generator output prior to test.
CAB1001 Inrush Compensator IEC 61000-4-11 Dips
The Conformity Assessment Business Model CAB1001 Surge Inrush Compensator enables users to meet the 500A inrush requirement of EN 61000-4-11 irrespective of supply impedance.
ESD-Sense Quick pre-check of IEC 61000-4-2 ElectroStatic Discharge
The ESD-Sense has been developed with EMC test laboratories in mind to enable a “go / no-go” verification of the ESD generator output prior to test.
PG 6-401, Capacitor Tester, 6kV
The High-Voltage Pulse Generator Type PG 6-401 is designed for dielectric testing of X- and Y-capacitors with standard impulse voltages 1.6/47 µs up to 6 kV acc. to IEC 384-14, etc. The generator has the same principle of operation as the IPG 809 but allows testing capacitance values of 33 nF - 470 nF. Picture: incl. Option PA 503
IPG 250, Pulse generator 250V
The pulse generator IPG 250 is designed for measuring the step response of high-impedance networks, for instance voltage dividers, oscilloscope probes etc. The generator excels by calibrated adjustment of output amplitude, short rise time and flat pulse top. The output pulse amplitude can be adjusted by use of a 10-turn potentiometer from 0 to 250 V. Positive and negative polarity can be selected.
Automotive Transients to FORD and JLR
This is one-off design and development of the transient generator specified in JLR Specification JLR -EMC-CS v1.0 Amendment 4.
It gives a good reproduction of the required CI 220 and RI 130 transients.
Automotive FORD JLR CI250 Timing Jig
This is for JLR-EMC-CS V1.0 Amendment 4 test CI 250. This provides the millisecond / sub-millisecond timing pulses over a 60 s period for each of the four required test sequences for the CI 250 immunity to ground offset test. It feeds directly into the "Trigger In" on the arbitrary waveform generator to produce the required transient trigger sequence.
ESD-Soft 6: Control software for ESD
The Microsoft-Windows based software controls the ESD generator via a serial interface
HILO Remote, For HILO/TEST Gernerators
Hilo Remote Control is software for personal computers. It is used to control HILO-Test generators from your computer. The software allows users to create tests and reports, which can be changed with your default text editor. In addition, it allows an oscilloscope to monitor all test pulse and to store the captured image of the waveforms on the computer. The communication with the generator is implemented with a LAN connection. The generator is connected via an optical interface. Thus, the PC is completely disconnected from the generator.
CAR Cal Kit, Standard loads for Automotive Testing
In accordance with the pulse verification requirements given in Annex C of ISO 7637-2:2011 and Annex A of ISO 16750-2:2012, test pulses generated by automotive transient generators need to be verified both under no-load (open circuit verification) and loaded conditions with specified loads.
CCK, Capacitor Calibration Kit for: PG10-200, PG12-360 and PG20-100
The Capacitor Calibration Kit CCK has been designed to measure the pulse output voltage of surge generators PG10-200, PG12-360 and PG20-100. IEC 61730-1/2, IEC 60060-2
