TBCP1-200/250/500 RF Current Monitoring Probe
TBCP2-250/500/750/30k400 Clamp on RF Current Monitoring Probes
TBCG1 Radiating Comb Generator
TBCG2 Comb Generator/Frequency Multiplier
TBCG3-RN2 Comb Generator, 5 kHz-2 GHz, for RE
TBCDN-M1, CDN, 1-line Power Mains, 15A, 300V AC, 600V DC
TBCG3-RN6 Comb Generator, 5 kHz-6 GHz, for RE
TBCCP1-400K600 COAXIAL RF CURRENT MONITORING PROBE
TBCG3-CN Comb Generator, 5 kHz-2 GHz, for CE
TBCP3-1000 RF Current Monitoring Probe
TBCP4-250/500/750 Clamp on RF Current Monitoring Probe
Products
TBLM01 - Line Impedance Stabilization Network Mate
The TBLM1 LISN Mate is a companion device for LISNs, which splits the conducted noise signal into its common mode and differential mode components. The LISN Mate is connected to the output of a LISN inserted into the positive supply line and to a second LISN inserted into the negative supply line.
TBCP1-200/250/500 RF Current Monitoring Probe
The TBCP1-200, TBCP1-250, and TBCP1-500 is fixed aperture RF current monitoring probe, expanding the Tekbox product range of affordable EMC pre-compliance test equipment. The probe has a 3dB bandwidth of approximately 200 MHz and is characterized and usable over the frequency range from 10kHz to 500 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 (500) MHz.
TBCP2-250/500/750/30k400 Clamp on RF Current Monitoring Probes
The TBCP2-250, -500, -750 -30K400 are snap-on RF current monitoring probes with very flat response of a 3dB bandwidth.
TBCG1 Radiating Comb Generator
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
TBCG2 Comb Generator/Frequency Multiplier
The TBCG2 is a passive, step recovery diode based comb generator/frequency multiplier. It is optimized for moderate drive power and spectrum flatness in the frequency range 1 MHz to 2.5GHz. The recommended drive power is +10 dBm to +20 dBm The frequency range for the drive signal is 1 MHz to 350MHz
TBCG3-RN2 Comb Generator, 5 kHz-2 GHz, for RE
The TBCG3-RN2 comb generator is primarily intended for testing radiated emission setups. It is a useful tool for validating the proper operation of the antenna and pre-amplifier, as well as the accurate set-up and configuration of the spectrum analyzer.
- 5 kHz-2 GHz,
- switchable 5, 10, 25, 50, 100 MHz,
- external: 5 kHz-200 MHz,
- 6xNiMH, AA, Charger,
- 2 monopole antennas
TBCDN-M1, CDN, 1-line Power Mains, 15A, 300V AC, 600V DC
The TBCDN-M1 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6. The TBCDN-M1 is compliant with IEC 61000-4-6 Annex D2.
TBCG3-RN6 Comb Generator, 5 kHz-6 GHz, for RE
The TBCG3-RN6 comb generator is primarily intended for testing radiated emission setups. It is a useful tool for validating the proper operation of the antenna and pre-amplifier, as well as the accurate set-up and configuration of the spectrum analyzer.
- 5 kHz-6 GHz,
- switchable 5, 10, 25, 50, 100 MHz,
- external: 5 kHz-200 MHz,
- 6xNiMH, AA, Charger,
- 2 monopole antennas
TBCCP1-400K600 COAXIAL RF CURRENT MONITORING PROBE
The TBCCP1-400K600 is a coaxial RF current monitoring probe with a 3 dB bandwidth from 400 kHz to 600 MHz and a very flat response from 1 MHz to 200 MHz.
TBCG3-CN Comb Generator, 5 kHz-2 GHz, for CE
The TBCG3-CN comb generator is primarily designed to verify conducted emission test setups. It is a useful tool to validate the correct operation of the LISN, correct set-up, and correct configuration of the spectrum analyzer.
- 5 kHz-2 GHz,
- switchable 0.1, 0.5, 1, 5, 10 MHz,
- external: 5 kHz-300 MHz,
- 4xNiMH, AA, Charger,
- Country-specific adapter cables DUT socket of the LISN
TBCP3-1000 RF Current Monitoring Probe
The TBCP3-1000 is a fixed aperture RF current monitoring probe. It has a very flat response with a 3dB bandwidth of 1 GHz and is characterized and usable over the frequency range from 30kHz to 1 GHz.
The aperture of the RF current monitoring probe is 17 mm. Its transfer impedance is close to 20 dB Ohm in the range from 3 MHz to 1 GHz.
TBCP4-250/500/750 Clamp on RF Current Monitoring Probe
The TBCP4-250, -500, and -750 is a fixed aperture RF current monitoring probe, it has a very flat response with a 3dB bandwidth of 750 MHz and is characterized and usable over the frequency range from 10kHz to 800 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is close to 14 dB Ohm in the range from 400 kHz to 750 MHz.
