TBMA6-P, 9 kHz – 30 MHz Passive Loop Antenna
EMCVIEW PC SOFTWARE PRE-COMPLIANCE TESTING
TBOH02 - Self Powered Active Load
TBTC0/1/2/3 - Open TEM Cell for EMC Pre-Compliance Testing
TBL50100-1B 50uH Line Impedance Stabilization Network LISN
TB Coax Cable Assemblies
TBMDA1 - 25 MHz - 3 GHz, 9dBm, Modulated Wideband Driver Amplifier
TBMDA4B - 100 kHz - 75 MHz, 20W, Modulated Power Amplifier
TBMDA3B - 10 MHz - 1 GHz, 8W, Modulated Power Amplifier
TBCH - Cable Holders
TBGP - Roll Up Ground Plane
Products
TBMA2, 30 - 300 MHz, BICONICAL ANTENNA
The TBMA2 is a biconical measurement antenna for EMC radiated emission testing and generating defined field strength. With its affordable price, it is an excellent choice for any lab carrying out in-house pre-compliance testing.
It is characterized from 30 MHz to 300 MHz and has a directional pattern similar to a dipole antenna.
TBMA6-P, 9 kHz – 30 MHz Passive Loop Antenna
The TBMA6-P is a passive Loop Antenna for affordable EMC pre-compliance testing. It has a frequency range of 9 kHz – 30 MHz, according to CISPR 16.
EMCVIEW PC SOFTWARE PRE-COMPLIANCE TESTING
The Tekbox EMC compliance software EMCview for PCs is a user friendly EMC pre-compliance testing of radiated and conducted emissions. It is a perfect complement for automated testing using our LISNs and TEM Cells. A built in amplitude correction enables correction and conversion coefficients for cables, amplifiers, attenuators, LISNs, TEM cells, antennas, RF current probes, striplines and capacitive coupling clamps.
TBOH02 - Self Powered Active Load
The TBOH02 is a self-powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable the accurate setting of current or resistance. Furthermore, it can be controlled by an external voltage.
TBTC0/1/2/3 - Open TEM Cell for EMC Pre-Compliance Testing
Radiated emission tests are typically carried out in anechoic chambers, using antennas to pick up the radiated signals. Due to bandwidth limitations, several antennas are required to cover the complete frequency range. Furthermore, it requires much space and the cost of the equipment for a standard conformant setup is immense.
TBL50100-1B 50uH Line Impedance Stabilization Network LISN
The TBL50100-1B 50µH is a single channel 50 ohm // 50 µH LISN for the frequency range 150 kHz – 30 MHz according to CISPR 16-1-2. In addition to conducted noise measurements on AC or DC supplied equipment, the LISN can be used to establish a defined impedance for a variety of other standardized tests.
TB Coax Cable Assemblies
Compleat your pre-compliance setup with premade coax cables.
TBMDA1 - 25 MHz - 3 GHz, 9dBm, Modulated Wideband Driver Amplifier
The TBMDA1 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its gain of 22 dB and 1dB compression point of +22dBm, it can boost the output power of a tracking generator up to 150mW.
TBMDA4B - 100 kHz - 75 MHz, 20W, Modulated Power Amplifier
The TBMDA4B modulated wideband power amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers.
TBMDA3B - 10 MHz - 1 GHz, 8W, Modulated Power Amplifier
The TBMDA3B modulated wideband power amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers.
TBCH - Cable Holders
The TBCH1 and TBCH2 wall mount cable holders are efficient and neat solutions to store laboratory cables. The TBCH1 cable holder is designed with a focus on storing RF cables and oscilloscope probes. The TBCH2 is ideal for banana cables.
TBGP - Roll Up Ground Plane
Many EMC pre-compliance test setups require a ground plane. Not every lab has the necessary space for the permanent installation of a sheet metal ground plane.
